Comments

• 

  Richard Kennedy November 26, 2014 at 1:07pm

  Doug

  I assume you looked into going to an earlier version?

  All I can say oh boy.... here we go.
• 

  Doug Walmsley November 26, 2014 at 5:31am

  @ Nathaniel and @Paul,

  This crazy feature can not be turned off.  I went into Configure tab and deselected "Show Airports" and only the broken rings around airports disappeared.

  I live inside the outer ring of this large and circle and can barely see anything under it.  This is annoying to say the least.
• Moderator

  Nathaniel Caner November 25, 2014 at 5:51pm

  @Doug,

  I believe that is identifying the Washington, DC Metropolitan Area Special Flight Rules Area (or the "ADIZ" Air Defense Identification Zone).

  I don't think there is a way to disable it. You can turn off the airports, but I don't see a way to disable the display of these zones. It's interesting that it doesn't effect the Flight Planning page, just the Flight Data page. That really makes the Flight Data screen unusable for the Baltimore area in the zone.

  

  Regards,

  Nathaniel ~KD2DEY
• Paul G. November 25, 2014 at 5:27pm

  It is the airport overlay, if you hover your pointer over the red circles they will show you the airport name.  Baically to show you when you are close to an airport. You can turn it off in the configuration tab, as detailed in this post:

  http://diydrones.com/forum/topics/mission-planner-1-3-2
• 

  Doug Walmsley November 25, 2014 at 4:32pm

  What is this on my map and how do I turn it off?!?!?

  It showed up when I downloaded the latest Mission Planner?
• 

  Richard Kennedy October 5, 2014 at 8:10pm

  @Austin

  I recently had an issue where checking the reverse box [ in AMP Planner ] didn't reverse it as it should but if I did so in the full param list it did. 1 is normal  -1 is reverse.

   
• Chris Leech September 10, 2014 at 4:29pm

  Just throwing this into the mix here and I apologize if it is not the correct forum gents, but there is little time left to take advantage of this great offering. I thought it my duty to bring to your attention this invention from a German group of engineers that may very well put to rest much of FAA worries about LOS/ FPV and Drones falling out of the sky. Check this out. I signed up for an "Early Bird" of this device called the AP Manager (by Gizmotec) that combines two FC's of your choice (their test set up uses two Pixhawk, but it can be any combo, mix or match) and even if both fail it will still control a multirotor or fixed wing craft via the onboard Rx. Watch this http://igg.me/at/AP-Manager/x
• Developer

  Randy September 2, 2014 at 5:29am

  @Austin,

  Make sure that on the MP's radio calibration screen, the green bar for the pitch moves in the opposite direction to the physical stick on your transmitter.  If it moves the wrong way, fix it in the transmitter not by adjusting any arducopter parameters.
• 

  Austin Laws September 1, 2014 at 2:28pm

  Pixhawk elevator/pitch reverse issue. I just can not get the pixhawk to reverse at all. reverse on my aurora 9 but makes no odds. pick up quad and aileron is fine when I lean it to the right the right motors spin up to relevel it same as when I do it on the left side. but when it comes to the elevator I lean it backwards and the back motors slow down. totally fed up and utterly confused. Can someone else?
• Spencer Willis July 25, 2014 at 2:22am

  Thanks mP1. Unfortunately we are leaving early Monday morning so I can't really get it quickly enough from Sydney.

  @David - do you have a web portal? I will order from you in the future.