A sneak peek at the Walkera Voyager 4 after a long year of development.
Voyager 4 is a unique fusion of both aerodynamics and aerial video technology running on 2.4 gHz or 4G LTE with Apple IOS App. Something new, expanding the range as far as you c
Read more…Hi,
I saw a few posts on this group describing how to integrate some sensors but was unable to find how to actually port lets say the Wire.h library from older Arduino distributions. I want to know how to do this for Pixhawk and for the older ArduPilo
Read more…This Parallax brand prototyping board has everything you need to prototype electronics on a variety of platforms. Although designed for (and includes) a Parallax Propellor, because the board offers 5V and 3.3V logic and power, ANY platform including:
Read more…This kit boots right up into a touch screen GUI ready to run your favorite Linux code. This is the best way to learn BeagleBone and save hours of setup and wiring time; everything is plug-n-play and ready to go.
Unlike Raspberry Pi, the BeagleBone has
Is it possible to control the progression of a waypoint mission though an RC channel? So the knob at 50% and the quad will fly to 50% mark in the mission?
Read more…My drone flies well in stabilized mode but when in loiter it gets jerky and somewhat noisy. It still flies, but not like I would like. I have changed flight controllers, GPS's and motors not the Q-brain ESC. There is no issue until I go to loiter
Read more…Hi,
Is it possible to display the 'time in air' in minutes in stead of seconds?
thanks
Read more…I purchased the HAKRC Storm32 Controller/Gimbal from Gearbest (below). Unfortunately one of the motors was defective so Gearbest (after several emails) has agreed to issue a full refund, in store credit.
So I'm faced with a decision. Should I orde
Read more…Hi,
I have got Pixhawk (3.6.0) in my new plane but I am scared to fly in auto. If I set ARSPD_USE to 1 the hud starts to jitter, Even more I blow in to sensors tube the horizon starts to move (my plane is on the table). See the video.
Read more…Hi all,
Brand new, learning quickly, and very excited.
I've got a pixhawk board v3.3.3, mission planner 1.3.39, taranis transmitter, and the X8R receiver running PPM out of the SBUS port. The transmitter has 5 channels set up, throttle (1), roll (2),
Read more…Hi all,
So I've bought a HackRF and been playing around with it, but I thought maybe someone could help me out with something. I'm trying to replicate the following 'hack', but then with an XN297 transceiver chip (instead of nRF24..):
http://blog.ptsec
Hi everyone,
I've built several quads before at a weights of 500 grams, 2kg, and 3kg so I'm not totally new to motor selection but it's taken me forever the last few times.
I'm getting ready to build a quad with a weight of 900 - 1000 grams and a prop
Read more…Hi,
I'm a student researcher working on a jet engine powered UAV. The task is to control the flight using pixhawk autopilot.
I have done few HIL simulations with my custom built aircraft inside X-Plane and customized gain parameters in pixhawk. The r
Read more…I have a proplem when switch mode into auto.during flying when switch mode into auto the plane start to dive and crash into the ground.Iam use apm2.8
Read more…Hello!
I am looking for some help developing an interface between the Ardupilot SITL simulator and MATLAB/Simulink.
I am part of a research team in the early stages of developing a high-fidelity model of multi-rotor aircraft. We have access to state-
I just installed the update to MP 1.3.39 and realized that the Dataflash auto analysis is broken.
.bin files I could auto-analyze in the previous version of MP result in a "Failed to start LogAnalyzer" followed by a bad input file message wit this rel
Read more…Hi Guys,
I am currently starting out with my first drone, a hexacopter using pixhawk as the flight unit, Tiger Airgear motors and skywalker quattro 25Ax4 ESC.
6 Tiger Airgear 2213 Motor
2 Quattro 25Ax4 (4 in 1 esc)
We connect 3 motors to one of the esc e
Read more…Hi Guys,
I am currently starting out with my first drone, a hexacopter using pixhawk as the flight unit, Tiger Airgear motors and skywalker quattro 25Ax4 ESC.
6 Tiger Airgear 2213 Motor
2 Quattro 25Ax4 (4 in 1 esc)
We connect 3 motors to one of the esc e
Read more…Looking for an alternative to external led & usb or a wire diagram to make my own for my pixhawk so I can mount it in a shell
Read more…My brother is going to travel to New York and He is searching for an Rc planes shop in New York (preferible Manhattan) any advice? Thank's
Read more…