Comments

• Chris Thiesen August 2, 2015 at 10:08pm

  Hi hightechhobbie,  

  Have you worked with your TKOFF_ .... parameters? Don't think you should be able to throttle up with the RC in auto.  You're accelerometer takes care of this & kick's the throttle on after the plane has left your hand.  Set the delay with TKOFF_THR_DELAY to the appropriate time... 'For hand launches with pusher propellers it is essential that this is set to a value no less than 2 (0.2 seconds) to ensure that the aircraft is safely clear of the throwers arm before the motor can start.'

  Chris
• 

  whynotflydisquad August 2, 2015 at 2:34pm

  i can add the bin file if need be
• 

  whynotflydisquad August 2, 2015 at 2:33pm

  Hi, Im using a Pixhawk in a skywalker and mission Planner software for the GCS. when i fly in all modes FBWA  ,stabilize, manual , my throttle controll is fine but when i swithch into auto the motor wont turn on ?  can somone please help me on this. i have made sure i set the speed to 15 m/s  and when i read the waypoints it shows mr the DO-set speed to 15m/s.
• 

  Larry A Amati July 30, 2015 at 12:00pm

  Hello james,

                    I am using  a taranis radio and a x8R receiver.Also using Sbus on pixhawk. I connected gimbal tilt wire (white)&Black(gnd) to RC9 on pixhawk and used the recommended settings for the PWM's.RC9 is the 1st set of connectors on the right of the pixhawk.Also powered tarot gimbal with 12 volt UBEC.Hope this helps.
• James tate July 29, 2015 at 9:49am

  Real nice picture Larry, of yourTarot 680 pro hex.

  i have the same copter as you do and in final stages to fire it it up.

  I want to hook up my Gimbal Pitch and the retactable landing gear to the Pixhawk AUX ports, have you done this, if so how do you map it to AUX ports.

  I guess I could connect it straight to the Futaba R6802SB receiver I'm using , to the Channels 6,7,8 I have open on my Receiver, I'am using Sbus to Pixhawk on the RC port.

  I'm also using a Futaba RC 8TFG.

  What version of Firmware are you using, I'm using 3.3 RC8, they have been having a lot of Crashes on 3.2 Firmware

   
• 

  Larry A Amati July 29, 2015 at 8:02am

  Hi Guys, Just added a tarot 2 axis gimbal to my fy 680 pro hex.Connected it to the pixhawk as per settings.Works flawlessly.For ROI to work,the gps has to be locked on.
• garvarma July 22, 2015 at 11:36am

  I read that the Q brain 4in1 of 25A is compatible with pixhawk i think that i will buy to change by my emax.

  I will tell something when i will make some changes!
• 

  Jimmy Oliver July 22, 2015 at 10:24am

  What about: 

  Q Brain 4 x 25A?
• garvarma July 22, 2015 at 9:45am

  Hi,

  thanks Artem and arga firmansyah.

  arga, i read this time ago but i don't wanted to believe it till i don't check it. Do you have link (in emax website) where it says that emax 4in1 is not compatible with pixhawk?

  Artem i will try this that you say, by disable safety switch, but maybe problem is emax as arga say.

  thanks to everybody when i will try all possibilities i will say!

  thanks
• 

  arga firmansyah July 22, 2015 at 9:00am

  Hi gavarma, i face your problem 6 months ago.

  finally i found that emax 4in1 esc is not compatible with pixhawk. It confirmed on emax website as well. I finally then replace the esc that previously working great with apm.