About

Gender

Male


Please tell us a bit about your UAV interest

FPV flights


Hometown:

Saskatoon


Activity Feed

Oscar replied to Daniel Lap's discussion Looking for interested drone builder in new drone idea
"what makes your idea so special?"
Apr 11, 2015
Oscar replied to Erick's discussion Looking for a business partner/engineer
"what's the wing span and what is your target market?

Thx.

Oscar"
Apr 11, 2015
Oscar commented on Crispin's blog post FLIR Tau2 640 + GoPro and 3D printed case
"looks good. are you using that with a stabilizing gimbal?"
Mar 6, 2015
Oscar posted a discussion
Hello, I'm a bit confused about the throttle control logics here: In auto mode and FBWA modes, the throttle works while the plane is on the bench.I have it set up to hand launch in auto mode, and i would pretend to throw the plane and the motor…
Mar 4, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Hi Hein, email sent, thanks. Oscar"
Jan 17, 2015
Oscar commented on IKE's blog post Canada’s regulations for foreign commercial UAV operators
"Most of the time SFOC is only required for commercial use in Canada, majority of the drones under 2kg for recreational use is exempted from needing a SFOC. There are some criteria that apply, such as always maintaining a line of sight."
Jan 13, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Thanks Swift, no I don't use any of the free software you just mentioned, I am a working professional engineer and I have access to expensive commercial softwares."
Jan 13, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Hi turdsurfer, these heat sinks are included in kit here: http://tinyinvention.com/minimosd-v1-2-cooling-kit.html, you could also purchase them on their own on ebay, search for 11X11 mm heatsinks, 8x8 mm heatsinks should work too.
Oscar"
Jan 12, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Thanks Nick. The heatsink you described needs to be specially made, I can probably make one but I cannot print metal but there are some commercial operations that could. 
But to keep things simple, the bottom of the PCB is elevated from bottom of…"
Jan 12, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Thanks Hugues, I like your suggestion. I'll add the markings to the ports."
Jan 11, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Thanks Hein,
you can order it from here: http://tinyinvention.com/minimosd-v1-2-cooling-kit.html
Regards,
Oscar"
Jan 11, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"mP1, the case is there so the heat sinks don't get knocked around by wires and what not, also makes the OSD easier to attach to surface, to grab and remove, etc."
Jan 11, 2015
Oscar commented on Oscar's blog post MinimOSD Cooling Kit / Enclosure for V1.1 and 1.2
"Hi Nathaniel,
The reason I kept the heatsinks below the case is to provide protection and support for it so it won't get knocked around in hard landings if the enclosure detaches from velcros somehow. The heatsinks are larger than the surface of the…"
Jan 11, 2015
Oscar posted a blog post
After burning out a 3DR MinimOSD V1.1 from powering it for too long on the ground during testing a while back, I printed an enclosure kit with two large heat sinks for it.  The 3DR version of MinimOSD V1.1 (with straight video pins) sit in there…
Jan 11, 2015
Oscar replied to Oscar's discussion Dual OSD?
"Thanks. I see.

Is there any software that can overlaying log data onto the video without too much trouble?"
Oct 1, 2014
Oscar posted a discussion
Hi, I have two cameras onboard, I want to have the OSD in the high resolution onboard recording (as well as the low resolution FPV one). Is it possible to have two OSD connected in parallel from the Pixhawk?Or is there some other better way of doing…
Sep 30, 2014