Gender
Male
About
Location
BZ
Please tell us a bit about your UAV interest
APM hardware/ implementation on some aerial devices
Activity Feed
"Hi
Can you share the gimbal 3d files?
It is looking very good!
Thank you
Regards
Adrian"
Can you share the gimbal 3d files?
It is looking very good!
Thank you
Regards
Adrian"
"Can this setting be added to the official mission planner?"
"Nice eagle tree osd telemetry+minim osd + video link on 5.8 "
"Could it be added a function for PAN to show the ardustation the exact direction of 0,90,180,270 degr of the servo travel to increase precision .
Today my servo was moving in another movie prior to the plane position .180 degr was ok but the rest…"
Today my servo was moving in another movie prior to the plane position .180 degr was ok but the rest…"
"Hi
I appreciate your help and I think that I am not the only one.
I would send you a beer on your paypal account.
(my GS is working fine now but I think that could go better)
If you will post the update I will test it also and give a report."
I appreciate your help and I think that I am not the only one.
I would send you a beer on your paypal account.
(my GS is working fine now but I think that could go better)
If you will post the update I will test it also and give a report."
"Hi
I flew today. Prior to this flights I was very confident in my EasyStar.2 autonomous flight capabilities. Now .... it is TUNNING ALLL over again with the new TECS.I hope to have the time and perseverance to have the same results as the other…"
I flew today. Prior to this flights I was very confident in my EasyStar.2 autonomous flight capabilities. Now .... it is TUNNING ALLL over again with the new TECS.I hope to have the time and perseverance to have the same results as the other…"
"Hi
Now I understand the limits of this board. For now it works ok and I don't have a viable alternative (jDrones ArduStation Mega v1.5 laks the manual, support and implementation along the mission planner). I will wait till someone makes a GUI for a…"
Now I understand the limits of this board. For now it works ok and I don't have a viable alternative (jDrones ArduStation Mega v1.5 laks the manual, support and implementation along the mission planner). I will wait till someone makes a GUI for a…"
"this is the line for blocking the 3 turns at start up?
#define SERVO_MAX 2600 //Range of servos pitch and roll#define SERVO_MIN 400
How to transform this in defining lower usecs just for the pan?
About the I2C port do you think that it can be added…"
#define SERVO_MAX 2600 //Range of servos pitch and roll#define SERVO_MIN 400
How to transform this in defining lower usecs just for the pan?
About the I2C port do you think that it can be added…"
"Finally the Ardustation goes in the good direction. If someone can show how to add a magnetometer and/or GPS to this old board it would be greatly appreciated.
Just played with the settings for pan servo:…"
Just played with the settings for pan servo:…"
"MANUAL ,INSTRUCTIONS?"
"Very interesting! How do you make the translation from flying wing to tricopter?
Can maybe someone convert apm 2.5 from arducopter to arduplane with only one switch?"
Can maybe someone convert apm 2.5 from arducopter to arduplane with only one switch?"
"Hi Heino,
Thank you for your quick answer, I wasn't expect such a quick one due to my last call for this problem on another thread "few" monhts ago.
Couldn't be easer for all of us if someone put a line of code to correct directly the travel of the…"
Thank you for your quick answer, I wasn't expect such a quick one due to my last call for this problem on another thread "few" monhts ago.
Couldn't be easer for all of us if someone put a line of code to correct directly the travel of the…"
"HiWhen I use "Antenna test " from ardustation on PAN settings from 90 to 95 my 360deg winch servo goes 90deg - how can I correct that / where in the code.Thanks for you time "
"ANYONE?"
"If it is so good documented like the previous one .... i can't put my money on something that I didn't saw working at full capacity. "
"Hi
When I use "Antenna test " from ardustation on PAN settings from 90 to 95 my 360deg winch servo goes 90deg - how can I correct that / where in the code.
Thanks"
When I use "Antenna test " from ardustation on PAN settings from 90 to 95 my 360deg winch servo goes 90deg - how can I correct that / where in the code.
Thanks"
