Gender
Male
About
Location
Melbourne
Please tell us a bit about your UAV interest
VTOl Tilt Rotor NIght Vision AutoPilor
Hometown:
Australia
Activity Feed
"Cool design, will it work with auto-mode?"
"Ian,
Just find the reason it doesn't fly well: gps of naza-lite needs to be recalibrate if you haven't used for a while. I took the gps off the big quad and put it on my F450, the quad shift when it is on >6 satelliates, and after I redo the…"
Just find the reason it doesn't fly well: gps of naza-lite needs to be recalibrate if you haven't used for a while. I took the gps off the big quad and put it on my F450, the quad shift when it is on >6 satelliates, and after I redo the…"
"Ian-I had few flight was my huge quad and find out that it seem to react really slow, I am using a naza lite with gps, but it doesn't over really stable, and return to home doesn't work with the drone.
Please let me know if what's best…"
Please let me know if what's best…"
"Simple, and easy to use."
"Ian,
I used 4* 600mm tubes on the drone, the frame is Tarot ironman 650 but I almost made it 900, so it's about 900mm width?It flown quite good, except I haven't test it with 2*5000mah 4S batteries yet, I might do it this weekend if everything goes…"
I used 4* 600mm tubes on the drone, the frame is Tarot ironman 650 but I almost made it 900, so it's about 900mm width?It flown quite good, except I haven't test it with 2*5000mah 4S batteries yet, I might do it this weekend if everything goes…"
"Just made this quad, and it is about 900mm wide, and here's the photo
4*5010 360kv rctimer motor
17*5.5 rctimer props
will post more photo and specification."
4*5010 360kv rctimer motor
17*5.5 rctimer props
will post more photo and specification."
"I am using the same motor and prop, building a huge quad this weekend."
" Hey elad,
How do you make a diy joystick recognizable via USB?
I am thinking make a rc controller like joystick for Android based ground station using controller's joystick like the one below.
Thx,
Andrew"
How do you make a diy joystick recognizable via USB?
I am thinking make a rc controller like joystick for Android based ground station using controller's joystick like the one below.
Thx,
Andrew"
"Congratulations on the software!
Is that possible to use joystick instead of rc control on a flat tablet? And, is that possible to use multiple port hub on android?
Thx for your hardwork."
Is that possible to use joystick instead of rc control on a flat tablet? And, is that possible to use multiple port hub on android?
Thx for your hardwork."
"Hey David,
I have recently find out a issue with control gimbal on a multicopter with one Trasmitter instead of two transmitter that both transmitter. Instead of explain, here is my diagram.
The reason I choose…"
I have recently find out a issue with control gimbal on a multicopter with one Trasmitter instead of two transmitter that both transmitter. Instead of explain, here is my diagram.
The reason I choose…"
"Good Job Elad, but there is some potential issue needs to point out:
1.H
2.Rainproof, nothing really, just capable for expected mission!"
1.H
2.Rainproof, nothing really, just capable for expected mission!"
"Hey David -Thanks for be in touch,
I am looking for Apm 2.5 to put onto my new tricopter, do you the best place to get them?
I don't log on a lot.So, Just leave a comment for me
"
I am looking for Apm 2.5 to put onto my new tricopter, do you the best place to get them?
I don't log on a lot.So, Just leave a comment for me
"
