Gender
Male
About
Location
Italia
About Me:
Vai sempre avanti e non tornare mai indietro. FPV
Please tell us a bit about your UAV interest
APM 2.5 - F450 - 4x ESC Skywalker 20A - 4x EMAX MT2213-935KV - GPS UBLOX NEO 6
Hometown:
Lecce (Italy)
Activity Feed
"I solved the problem .. the problem was due to a de-sync, corrected by replacing the firmware"
"Hi everyone, I need support to understand a problem that my new model with pixhawk and AC 3.2.1.The model to counter function properly without propellers.
When I try to fly if I make slow movements is all okey, but if I accelerate abruptly quad…"
When I try to fly if I make slow movements is all okey, but if I accelerate abruptly quad…"
"Hello everyone, my apm has once again freezer in flight, falling 7m do not understand why. We are off again all 4 engines for no reason, can someone give me a hand?
LOG:
https://drive.google.com/file/d/0B6QJRmFQmku9djcxTlpLOEpCRzQ/edit?u..."
LOG:
https://drive.google.com/file/d/0B6QJRmFQmku9djcxTlpLOEpCRzQ/edit?u..."
"you can supply a fault of the APM, the last vcc voltage is detected 4,96volt then I had the impression of a freeze, because even when I recovered the model apm had the red LED on and not blinking blue LED (GPS) off. Today I investigate with the same…"
"I do not think it is a battery problem, I have yet to calibrate the current sensor, but in addition to telemetry apm, I had the data of the voltage of my aurora 9 with optima 9 and if I remember correctly was around 10,7volt. The alarm is set to…"
"Hi all, I was conducting rehearsals with a gimbal, but the engines of height a few feet of my multicopter went away, I was just taken off and stabilize. Fortunately no damage ... but it's really dangerous! Randy Take a look at my log, in the final…"
"I fly with 4 Afro Slim 20A no problem!"
"Hi Randy, I was just trying to do a bit of hovering to test pixhawk with my TMotor mt3506 650kv motors with propellers 14". After takeoff everything seems ok,and altholt is ok, but there are problems with the loiter ruth..
With apm2.6 instead is a…"
With apm2.6 instead is a…"
"Hi all,
I experienced an issue on the first attempt to fly with rc6, I upgraded from rc5 to rc6 keeping the same parameters.
After arming the engines, they do not start.
Are initiated only by raising the quad
Watch the video…"
I experienced an issue on the first attempt to fly with rc6, I upgraded from rc5 to rc6 keeping the same parameters.
After arming the engines, they do not start.
Are initiated only by raising the quad
Watch the video…"
"hi all, I have a question maybe trivial:
Why with AC 3.1 rc5 (after start-initialization APM 2.5 ), I have the yellow LED solid?
Calibrations prearm OK.The motors arm are started correctly..
thx
G."
Why with AC 3.1 rc5 (after start-initialization APM 2.5 ), I have the yellow LED solid?
Calibrations prearm OK.The motors arm are started correctly..
thx
G."
"Hi Randy,
i want to replace the barometer of APM with a new one.
http://www.raspberrer.com/resistenze-termistori-diodi-ldr/375-ms561...
is it possible?
theoretically should be replaced with the new i2c address in the source code and recompile the…"
i want to replace the barometer of APM with a new one.
http://www.raspberrer.com/resistenze-termistori-diodi-ldr/375-ms561...
is it possible?
theoretically should be replaced with the new i2c address in the source code and recompile the…"
Hi all,I want to replace the barometer of APM with a new one.http://www.raspberrer.com/resistenze-termistori-diodi-ldr/375-ms561... it possible?theoretically…
"hi all,
I have a problem,
after updating the firmware with the latest relase and subsequently updated the character set with Latest_Charset.mcm
but always visualize these writings:
can anyone help me? please"
I have a problem,
after updating the firmware with the latest relase and subsequently updated the character set with Latest_Charset.mcm
but always visualize these writings:
can anyone help me? please"
