Gender
Male
About
Location
Port Orange, FL
About Me:
Currently a student at Embry Riddle Aeronautical University. Presidnet of Unmanned Aircraft Systems Technology Club on campus.
Please tell us a bit about your UAV interest
I fly FPV and would like to futher my knowledge in UAV/UAS.
Hometown:
Wilson NC
Activity Feed
"Hey look... That guy looks familiar :D"
"Seppo, could I use this antenna on the RFD 900 and still get 20+ miles or would this antenna harm the unit running it a full power? Im looking for the sleek form factor.
https://www.readymaderc.com/store/index.php?main_page=product_info&......"
https://www.readymaderc.com/store/index.php?main_page=product_info&......"
"Pulled the PM off and powered the board with the ESC and jumper and it works great!! THANKS :D"
So, I pulled out the ole Ruckus last night and put the good ole APM on it again. I have everything plugged up and I go to test it. Did the radio calibration and went to see if everything was responding right. To my surprise, the steering works, but…
"Problem solved!!! The problem lies within the design of the S800/F800. Because the arms are detachable, the connectors in which the pins on the arm contact the plate are soldered into the center plate. Those that have flown the S800 know that the…"
"The pitch is always in the same direction. When I did the ground test it would start to decrease speed and sputter then stop for a split second and then start back to normal speed. This would repeat every 20 seconds or so. There is a log file…"
"So, I did some ground testing today and found that after several seconds of the hex being powered up just below takeoff thrust, the front right motor would slowly begin to sputter to the point of shutting off for a split second and then starting…"
"Here is a screen shot of the pitch on the first log"
"so, I just changed out the rx/tx back to the borrowed one and this time, I am still having the pitch issue. It was not as violent this time, however I only allowed it to do it once and then landed immediately. Here is the log file with the Fly…"
So, Ive recently put APM on an RC Timer F800. The first few flights went very well. At the time, I was running a Futaba 8J. By the end of the first day, stabilize was spot on and the Hex was flying really well. On the second day of flight testing, I…
"Im using ArduPlane. I believe its version 2.78 on the APM and 1.3.0 as well as 1.3.1 on Mission Planner. I guess Ill try reloading my APM firmware as much as I'd hate to. My plane is flying like a dream and just as soon as I reload the firmware on…"
"Enable remote was checked and I double checked the pin count multiple times. It was working back when I had access to the Relay_Pin parameter. Now that it has disappeared from the parameter list, its not working. I have the check box for the…"
"So apparently I can no longer trigger my camera off of pin A9. The forums new CHDK page doesn't do a good job of how to connect everything with their new revamp of pin outputs (digital vs analog).A while back, I was using this tutorial for setup and…"
"wth happend to the camera_tiggger_dist and Relay_pin parameters??? They arent showing up anymore. Did they get removed from the full param list?"
"I just remembered, the GUI that comes up is not sized correctly for you to view the entire screen, I've been meaning to mention this to Tridge, but what Ive done so far is tab from a given field and count the number of tabs until it reaches the top…"
"@ Ryan Sales, save yourself the headache. Go to this link http://uav.tridgell.net/geosearch/ click on the geosearch-0.4.zip to download the file. Also download the libjpeg-turbo-1.3.0. Once these have downloaded, unzip the files. Now, you can open…"
