About

Gender

Male


Location

Port Orange, FL


About Me:

Currently a student at Embry Riddle Aeronautical University. Presidnet of Unmanned Aircraft Systems Technology Club on campus.


Please tell us a bit about your UAV interest

I fly FPV and would like to futher my knowledge in UAV/UAS.


Hometown:

Wilson NC


Activity Feed

Jamie Glover commented on Chris Anderson's blog post Enrollment climbing in college drone training programs
"Hey look... That guy looks familiar :D"
Feb 21, 2017
Jamie Glover replied to Seppo's discussion RFD900, RFD900+ - New long range radio modem
"Seppo, could I use this antenna on the RFD 900 and still get 20+ miles or would this antenna harm the unit running it a full power? Im looking for the sleek form factor.
https://www.readymaderc.com/store/index.php?main_page=product_info&......"
Jan 14, 2017
Jamie Glover replied to Jamie Glover's discussion Ardu Rover drive motor not working. Brownout results from commands. in ArduRover User Group
"Pulled the PM off and powered the board with the ESC and jumper and it works great!! THANKS :D"
Oct 30, 2014
Jamie Glover posted a discussion in ArduRover User Group
So, I pulled out the ole Ruckus last night and put the good ole APM on it again. I have everything plugged up and I go to test it. Did the radio calibration and went to see if everything was responding right. To my surprise, the steering works, but…
Oct 30, 2014
Jamie Glover replied to Jamie Glover's discussion Hex Pitches violently while in stabilize at random without user input
"Problem solved!!!  The problem lies within the design of the S800/F800. Because the arms are detachable, the connectors in which the pins on the arm contact the plate are soldered into the center plate. Those that have flown the S800 know that the…"
Aug 26, 2014
Jamie Glover replied to Jamie Glover's discussion Hex Pitches violently while in stabilize at random without user input
"The pitch is always in the same direction. When I did the ground test it would start to decrease speed and sputter then stop for a split second and then start back to normal speed. This would repeat every 20 seconds or so. There is a log file…"
Aug 10, 2014
Jamie Glover replied to Jamie Glover's discussion Hex Pitches violently while in stabilize at random without user input
"So, I did some ground testing today and found that after several seconds of the hex being powered up just below takeoff thrust, the front right motor would slowly begin to sputter  to the point of shutting off for a split second and then starting…"
Aug 9, 2014
Jamie Glover replied to Jamie Glover's discussion Hex Pitches violently while in stabilize at random without user input
"Here is a screen shot of the pitch on the first log"
Aug 7, 2014
Jamie Glover replied to Jamie Glover's discussion Hex Pitches violently while in stabilize at random without user input
"so, I just changed out the rx/tx back to the borrowed one and this time, I am still having the pitch issue. It was not as violent this time, however I only allowed it to do it once and then landed immediately. Here is the log file with the Fly…"
Aug 7, 2014
Jamie Glover posted a discussion
So, Ive recently put APM on an RC Timer F800. The first few flights went very well. At the time, I was running a Futaba 8J. By the end of the first day, stabilize was spot on and the Hex was flying really well. On the second day of flight testing, I…
Aug 7, 2014
Jamie Glover commented on Jeff Taylor's blog post APM to CHDK Camera Link Tutorial
"Im using ArduPlane. I believe its version 2.78 on the APM and 1.3.0 as well as 1.3.1 on Mission Planner. I guess Ill try reloading my APM firmware as much as I'd hate to. My plane is flying like a dream and just as soon as I reload the firmware on…"
May 5, 2014
Jamie Glover commented on Jeff Taylor's blog post APM to CHDK Camera Link Tutorial
"Enable remote was checked and I double checked the pin count multiple times. It was working back when I had access to the Relay_Pin parameter. Now that it has disappeared from the parameter list, its not working. I have the check box for the…"
May 5, 2014
Jamie Glover commented on Jeff Taylor's blog post APM to CHDK Camera Link Tutorial
"So apparently I can no longer trigger my camera off of pin A9. The forums new CHDK page doesn't do a good job of how to connect everything with their new revamp of pin outputs (digital vs analog).A while back, I was using this tutorial for setup and…"
Apr 25, 2014
Jamie Glover commented on Jeff Taylor's blog post APM to CHDK Camera Link Tutorial
"wth happend to the camera_tiggger_dist and Relay_pin parameters??? They arent showing up anymore. Did they get removed from the full param list?"
Apr 25, 2014
Jamie Glover commented on Andrew Tridgell's blog post Demonstration of CanberraUAV image search algorithm
"I just remembered, the GUI that comes up is not sized correctly for you to view the entire screen, I've been meaning to mention this to Tridge, but what Ive done so far is tab from a given field and count the number of tabs until it reaches the top…"
Jan 4, 2014
Jamie Glover commented on Andrew Tridgell's blog post Demonstration of CanberraUAV image search algorithm
"@ Ryan Sales, save yourself the headache. Go to this link http://uav.tridgell.net/geosearch/ click on the geosearch-0.4.zip to download the file. Also download the libjpeg-turbo-1.3.0.  Once these have downloaded, unzip the files. Now, you can open…"
Jan 3, 2014
More…