Gender
Male
About
Location
Neuquén
Please tell us a bit about your UAV interest
Aerial Filming
Hometown:
San Martin de los andes
Activity Feed
"Absolutely PRO. i'm sure you could make great success if you try to sell those motor mounts. how you do it? cnc machinering? and the plastic cap? injected or 3d printed? congrats!"
"you have heavily pulsating motors in loiter, worst than mine. you need to enable IMU logging in order to have vibrations measurement. enable it, do a test flight and post logs. we have similar issues. what motors/esc/props/lipo are you using?"
"you got itlog_usb_2016_03_27_18_11_37.tlog"
"had similar problem and was the ESC programming. they cut off some motors due to low battery. this esc feature needs to be disabled. you have it disabled on all esc?"
"no telemetry logs since i was using droid planner on my cellphone as ground station. if droid planner saves logs of telemetry data received, i'm not aware."
"Not responsive due to... WHAT?
STOP SPAMMING, GOOD BYE!!"
STOP SPAMMING, GOOD BYE!!"
"I think The only way to go is swapping 2 of 3 AC cables between esc and motors. If there id a software óption to reverse motor spin, i dont know. But is always better do things the way those things are expected to be done, rather than doing…"
"will give you only BarAlt, since GPS-Alt is out of chart. i live on Andes Range, 1000 meters avobe sea level. gps alt graph is nearly identical, but starts at 1000 value. Barometric altitude is measured with 0 at APM initialization."
"Well..... not a very nice day today!
I decided to do a previous step before autotune. try to spend all two batteries doing a quiet and nice althold flight, just to be sure of stabilty.
flight last only 1 minute or so...
take off in stabilize, and…"
I decided to do a previous step before autotune. try to spend all two batteries doing a quiet and nice althold flight, just to be sure of stabilty.
flight last only 1 minute or so...
take off in stabilize, and…"
"Yeah, sure it's heavier. a dipole will outperform this, and with less weight. only disadvantage on dipoles is the no signal spot under and over the antenna. it's a matter of testing!
meanwhile, you can always remove the rubber tube, and add some…"
meanwhile, you can always remove the rubber tube, and add some…"
Hi!I will share to you the repair and enhacement procedure i did to my Turnigy 9X8Cv2 receiver.The Rx comes with a minimal antenna, possibly 2dBi, monopole type.It's made of a full wavelenght mini coax cable, a sleeve balun to avoid detune from…
"Hello!
Today i'd make some progress. i managed to have 2 altHold flights, both very stable and easily controllable.
I did the on-flight Rate P roll & pich tunning, using a knob on the Tx. I got comfortable with the exact point where, if you do a…"
Today i'd make some progress. i managed to have 2 altHold flights, both very stable and easily controllable.
I did the on-flight Rate P roll & pich tunning, using a knob on the Tx. I got comfortable with the exact point where, if you do a…"
"Thanks Harry! i didn't want to state apm don't support autotune, sorry if i did that. My english isn't so good. I saw a lot of vids on youtube showing arducopter autotune on apm copters. i tried to ask what should i do first: Manual PID Tunning or…"
"Stephen: Thank you for taking the time to write. May be the windy conditions yesterday making a difference in my Z axis? i will read carefully the page you said. May autotune be a previous step to manual tunning? or is preferable to first do a…"
"Hi everybody..
Today i did an ESC calibration (all at once method) and balanced propellers. After that, i did a test flight, and the results are strange... the pulsating behavior when in althold mode diminished a bit, but still there. in the other…"
Today i did an ESC calibration (all at once method) and balanced propellers. After that, i did a test flight, and the results are strange... the pulsating behavior when in althold mode diminished a bit, but still there. in the other…"
"Hi! Thank you for your reply.
Since i'm on APM, a can not install 3.3, so i can't auto calibrate ESC. what should i do to calibrate ESCs manually?
vibrations are on the limits of acceptable levels stated on the wiki.
Seeing other posts i realized…"
Since i'm on APM, a can not install 3.3, so i can't auto calibrate ESC. what should i do to calibrate ESCs manually?
vibrations are on the limits of acceptable levels stated on the wiki.
Seeing other posts i realized…"
