Hi,I have a big problem, hope someone can help.When I updated my Pixhawk from V3.2.1 to V3.3+ I'm not able to calibrate Accel and Compass correctly.Here is what's happening:On the first connection after updating to V3.3 or V3.3.1 the voice is…
Hi everyone,I got trouble with my MinimOSD.Hope someone can help, please.Home Distance and Home Direction are not shown on my monitor when I use the OSD. I did select them and saved them to the OSD.Also the warning "NO GPS FIX" is showing even if…
"Yes, the Bluetooth module has a solid red and solid green light when I try to connect to APM.
I tried 2 different BT modules and 2 different APM's, but it's the same result. Both baud rates are 57600.
BT is paired to Android or PC and seems to have…"
Hi, I'm trying to use Bluetooth to communicate with my APM 2.6 telemetry port.So far changed the baud rate of my BT module to 57600, paired it successfully on my PC and Android Tablet, but can't get it work on both MissionPlanner and DroidPlanner.I…
HiI was curious if I can use my radio's expo and/or dual rate to fly my quadcopter.I want it to fly a bit more smoothly on the sticks e.g. indoor flight or for video recording. In other words less sensitive on the sticks.I'm not sure if expo and…
"Hi,
I have exact the same problem.
Bounces 1-3 times when I use Auto Land like with RTL.
My Throttle stick is always low before it touches down in auto land. So that couldn't be the problem.
I use the APM 2.6 with V3.1-rc7 firmware.
My TBS Disco…"
Hi everyone,I had my maiden flight today and it went not too bad... it's flying, but........of course some problems.I really need some help to solve them.- First of all in "Altitude Hold Mode" it goes slowly either up in the sky or down and…
Hi,I have a question to the FrSKY X8R receiver.Is it possible to use the conventional 8 PWM channels on the X8R and use at the same time the "FrSKY SBUS to PWM Decoder" to get 4 extra PWM channels, in all 12 PWM channels ?Also would I need the…
Problem !Twitches on my quadcopter only occur if the input of the APM's ch6 gets high input (100%). Like when a switch on the Tx is in position 1 or a nob is turned up.When I reduce the input of ch6 to about 50% or disconnect the wire to ch6…
"I found a half solution !!
Super Simple mode is enabled by setting the parameter named SUPER_SIMPLE to 1 (0 disabled default) in the Parameter List in the Mission Planner’s Configuration section.
If you've done this and set "simple mode" to ch7 or…"
"Problem found !!
The twitches occur only if the input of the APM's ch6 gets high input (100%). Like when a switch on the Tx is in position 1 or a nob is turned up.
When I reduce the input of ch6 to about 50% or disconnect the wire to ch6 input…"
Hi,I set the super simple mode to ch7 / ch8 at the Mission Planner APM:Copter Pids.When I was flying to test it, nothing happend. It seems super simple mode doesn't work if set on ch7 opt or ch8 opt.In the instructions under "simple and super simple…
"My TX/RX is only a simple Devo 10. Therefore I don't use PPM.
I used it on a different quadcopter and it worked fine.
I'll try to reset the APM and will see if this works and post the outcome soon.
Hi,I have some serious problems with my 3DR Quadcopter with APM 2.5 and 3.0.1 firmware.When I fly, the Quadcopter is twitching about ones every couple minutes in one direction. Forward, backwards, left right and even upwards. Also sometimes the…