Gender
Male
About
About Me:
Beginner with Ardupilot. Build & fly Octo and Hexacopter from Mikrokopter
Please tell us a bit about your UAV interest
Photography
Activity Feed
"Hi!
Sorry, but i am completely new in "traditional heli"
in the documentation i can not find anything about learning modes.
is it ok to use 3.1 for helicopters?
thanks"
Sorry, but i am completely new in "traditional heli"
in the documentation i can not find anything about learning modes.
is it ok to use 3.1 for helicopters?
thanks"
hi!Can you please tell me, if it is normal, that in acro mode with "flybar" the swash plate is moving when I tilt the helicopter.As far as I know, i have to use flybar if i have a helicopter with paddles - am i right?I use AC 3.1thanks
"i have the same issue. i ordered 2 boards. one is working fine, since i installed mp 1.1.16, the other has the same problem.
i use a 64bit win7 computer.
i really hope it´s not a bad board...
"
i use a 64bit win7 computer.
i really hope it´s not a bad board...
"
Hi! I finally build my Arducopter and loadet 2.0.50 firmware. All seems to work fine, exept one thing:The magnetometer is showing a wrong direction. I set the magnetic declination in the setup. Is there a way to calibrate the compass or is it done…
"exactly! that´s what i use."
"Hi Chris!
First, excuse my bad english.Congratulation for your great pice of software. The Video Background with the HUD is a really big improvement. Really nice!
Now I would have a idea for a very intersting, new feature. I have nevere seen this…"
First, excuse my bad english.Congratulation for your great pice of software. The Video Background with the HUD is a really big improvement. Really nice!
Now I would have a idea for a very intersting, new feature. I have nevere seen this…"
"SuperCharger: I guess it will update itself, if you choose check for update in th 1.0"
After a while, I am trying to get my APM´s running. Sometimes the APM´s restart by themselfe. I bought a really good and strong ESC, so power should not be a problem.What I can say, is that when I test the stabilization mode on the bench (rotating…
Hi! Do you suggest to use the APM Software released on January 10th or is it also possible to use the files from svn/trunk/the files from the svn are more up to date, but is it possible to fly a plane with them? Thanks Thomas
Hi! Due too big power problems with 2 boards I ordered a new APM at DiyDrones. Now I got a V1.4 with Atmeg 2560 onboard.Tho problem now ist, that i cant compile the code for a 2560. Is there a change, that there will be a update of the source code,…
"P.S. I also put the new hex file to the ppm chip. but i have a other hardware, and dit not dear to write the fuse bits also.
P.P.S. I´m gona to use 6 servos: 2 for aileron (via y-cable), 2 for flaps - directly from the receiver, 1 rudder, 1 elevator…"
P.P.S. I´m gona to use 6 servos: 2 for aileron (via y-cable), 2 for flaps - directly from the receiver, 1 rudder, 1 elevator…"
Hi all! Once I´d like to descripe some strange power behavior of the apm. I tested both verseions - the old board and the new board (1.0 and 1.4) with 2 different IMU shields.I tried 3 different power setups: power via the ESC: booting problems with…
"Hi Matin!
With no servos and power from esc it seems working.
1 servos no xbee over esc is ok. 2 servos sometime.
4 servos - no way
all are tiny servos (no hi current)
edit: gps and airspeed were connectet all the time - no problem with that.…"
With no servos and power from esc it seems working.
1 servos no xbee over esc is ok. 2 servos sometime.
4 servos - no way
all are tiny servos (no hi current)
edit: gps and airspeed were connectet all the time - no problem with that.…"
I realy need your help! First of all, excuse my bad english.I set up a plane with ardupilot mega and the imu sheeld. i attached followingublox gpsairspeed sensor4 servos (aileron with y-cable)xbee xbeexscesc to power whole system by my 3s lipomy…
