About

Gender

Male


Location

Corpus Christi, TX


About Me:

New to uav


Please tell us a bit about your UAV interest

Want to use GPS and also roll my uav


Activity Feed

jesse replied to David Nilosek's discussion 3DR radio telemetry but no parameters (or waypoints)
"Did you figure it out?  I am having the same issue as you describe."
Jun 28, 2014
jesse commented on Stefan Gofferje's blog post Updated: A closer look at DJI's no-fly zones
"Oh no, you gave in.  Sorry to hear that.  Apple Rules again.  Damit"
May 24, 2014
jesse replied to Mikeauknz's discussion In reality the Blade qx 350 failed to be Go Pro Compatible as advertised...Holy hell
"Oh, sorry.  

There was nothing wrong with the Quad or the GoPro, you should have done some research and you would of found that you can't fly 2.4 WIFI with a 2.4 Transmitter.  Please correct your posting as it is wrong.

Better?"
May 21, 2014
jesse replied to Mikeauknz's discussion In reality the Blade qx 350 failed to be Go Pro Compatible as advertised...Holy hell
"You have to be smart when flying devices like these.  Everyone know that you can't use a 2.4g TX with a 2.4g WIFI on the same quad.  If you don't know this then you have no business flying and make such a report as you did.  There was nothing wrong…"
May 21, 2014
jesse commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions...
"Thanks Thomas.  I was trying the latest version.  I did not notice there was another version of Arduino, I was trying 0022 and 1.0.1 I used 0100 now and it had uploaded the file. Where did you read this I missed it.  Now I have to test it out.…"
Jun 20, 2012
jesse commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions...
"I get this error when I compile.  I have no clue what to do.  Anyone care to help.  Thanks.

GCS_MAVLink\GCS_MAVLink.cpp.o: In function `mavlink_check_target(unsigned char, unsigned…"
Jun 20, 2012
jesse commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions...
"I ordered a FTDI cable so I will see if that works.  I am able the use APM Planner without any issues, so I'm sure my system is ok.  Thanks for your help I'll let you know once I get the FTDI cable."
Jun 9, 2012
jesse commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions...
"Chris, Garland just up the road.lol.  I am plugging in to the IMU shield(Blue Board).  I made the changes to the COM port but still no go.  Does it matter what is selected on the Tools/Programmer Menu?"
Jun 8, 2012
jesse commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions...
"Hello, I am using V1.4 APM but can't seem to get the Arduino to upload to the board.  I see it as com 8 but when I choose to upload it compiles then fails after a long time out.  I am lost, I feel lie I am missing some instructions but do not know…"
Jun 8, 2012
jesse commented on Earl's blog post Er9x transmitter now with MavLink
"Hello and thanks for the hard work on this hack.  I am having a problem and was hopeful I could get some help.  I have the 9x hack with smartieparts board installed along with the XBee from DIYdrones.  I get the heart beat signal but no data until I…"
May 19, 2012
jesse replied to Mark Zimmerman's discussion ArduCopter cannot fly anyway
"Are the props on up side down?  check the writing on the blades.
Also make sure your radio trims are 0.
On my quad just today it was tilting about 30 degrees forward on take off.  I tried looking at all the settings on my radio and connected to my…"
Apr 5, 2012