Gender
Male
About
Location
New York, NY
About Me:
Studying electronics
Please tell us a bit about your UAV interest
For fun
Activity Feed
HiMy Quad takes off properly.It's:APM 1.4 with latest ArduCopter code. Uploaded via Mission Planner.Did frame set to X modeIMU Shield is included with APM 1.4 MegaFrame is made from Balsa Wood. ESC: DualSky ESC 25AMotors: DualSky 980KV…
"Everything double checked.
Still in motor test just 2 motors spins. Got some takeoffs, but I want it to take of more stable.
Any ideas?"
Still in motor test just 2 motors spins. Got some takeoffs, but I want it to take of more stable.
Any ideas?"
"Hi
I see this data in MegaPlanner:
Is it normal?
"
I see this data in MegaPlanner:
Is it normal?
"
"I got a strange point, if it makes difference.
I go to terminal, I enter setup -> motors
Motor 1 spins a little and stops
Motor 2 spins a little and stops
Motor 3 no diff but waits necessary delay
Motor 4 no diff but waits necessary delay
Then…"
I go to terminal, I enter setup -> motors
Motor 1 spins a little and stops
Motor 2 spins a little and stops
Motor 3 no diff but waits necessary delay
Motor 4 no diff but waits necessary delay
Then…"
"Recent fly logs attachedalogs.zip"
"More images attached:
20120408_091954.jpg20120408_092002.jpg20120408_092008.jpg"
20120408_091954.jpg20120408_092002.jpg20120408_092008.jpg"
"Hi
Changes made during last hours, learned them here in comments.
a) Connected Ground and Signal connection on ALL ESCs.
b) Manually calibrated EACH ESC.
c) Balanced ALL propellers properly.
d) To protect noise and that extension cables which may…"
Changes made during last hours, learned them here in comments.
a) Connected Ground and Signal connection on ALL ESCs.
b) Manually calibrated EACH ESC.
c) Balanced ALL propellers properly.
d) To protect noise and that extension cables which may…"
Hi Here is my quad video: Power board doesn't exists, just I soldered + wires together and - wires together.APM 1.4 with latest ArduCopter code. Uploaded via Mission Planner.Did leveling process successfullyDid radio setup process successfullyDid…
"Don't know, but I think my entire problem is PID settings.
How can I find proper PID settings for my frame/motor/esc?
Thanks"
How can I find proper PID settings for my frame/motor/esc?
Thanks"
HiI'm going crazy about watching people's quadcopter videos and failing to build my own with most expensive devices and breaking and re-purchasing everything!Please tell me what I'm doing wrong.Motors: Dualsky Xmotor 3542CA-6 450W 940Kv (4x…
"P.S.
I don't have GPS (no need for now)
I checked manual and all possible solutions for myself, just I didn't understood this one:
"
Was the quad stable and flat for the whole calibration routine at startup? Was it stable and flat during the setup…"
I don't have GPS (no need for now)
I checked manual and all possible solutions for myself, just I didn't understood this one:
"
Was the quad stable and flat for the whole calibration routine at startup? Was it stable and flat during the setup…"
HiI have 2 3800mah battery, 3S with 30C power.Motors are 450w and 930KVPropeller 12x4.5Everything is set properly.ESC calibrated using auto mode (calibrated all ESCs at one time)Motors are sameArduPilotMega 1.4 with 2560 processorIMU Shield attached…
"My Power Distribution Board, any failure in this?
Thanks20120317_005240.jpg"
Thanks20120317_005240.jpg"
"Video on youtube:
https://www.youtube.com/watch?v=vi2Vm3fjHFQ"
https://www.youtube.com/watch?v=vi2Vm3fjHFQ"
