Gender
Male
About
Please tell us a bit about your UAV interest
making drones
Hometown:
eindhoven
Activity Feed
"Unfortunately it's not working with other firmwares.
It starts with 2 green blinks for some time then it stops.
I tried different baud rates and still no positive results."
It starts with 2 green blinks for some time then it stops.
I tried different baud rates and still no positive results."
I have a pixhawk board, I could upload AC3.2 firmware but then I can't connect the board to the mission planner. I tried different things: connect/disconnect GPS/compass module, tried on different USB port, even tried with separate power module but…
Hello everyone I recently joined the drone fields and i've got a small issue:My HexaCopter is not flying as it should be (the RUDDER is shifted to the ALI stick and the opposite is true)I didnt know how to switch it back to its original location…
"Thanks Anders
I will try to use another ESC because I tried more than 3 types of motors but this specific motor does not work.
I appreciate your time my friend.
Kind regards
Muhannad "
I will try to use another ESC because I tried more than 3 types of motors but this specific motor does not work.
I appreciate your time my friend.
Kind regards
Muhannad "
"I used a smaller brushed motor without gears and it works good with Tx, this specific brushed motor does not work with the Tx.
I tested it with connecting a 2S and a 3S batteries directly to the motor and it spins but when I connect it with the ESC…"
I tested it with connecting a 2S and a 3S batteries directly to the motor and it spins but when I connect it with the ESC…"
Hello everyoneI had this brushed DC motor and I wanted to connect it with the (AquaSpeed 50) ESC that have a forward and reverse function , and then I wanted to move the DC motor with one of the sticks in my taranis plus , but unfortunately I…
"I ve connected all the components together and everything should work but the amount of power used seems to be little and cannot power up the system I am using a (7.2V 800mAh ni-MH )battery is this enough ? or I should use a Lipo battery with more…"
"http://www.hobbyking.com/hobbyking/store/__41608__FrSky_X8R_8_16Ch_...
This is my Rx is it necessary to connect the speed controller to a specific input or it's up to me ?
I am working on it now and will let you know if there is an update.…"
This is my Rx is it necessary to connect the speed controller to a specific input or it's up to me ?
I am working on it now and will let you know if there is an update.…"
"Thanks Anders for your reply
So I ve got this speed controller (see attachment) is it going to work with the mentioned motor??
Is there any coding involved or it's just connections? "
So I ve got this speed controller (see attachment) is it going to work with the mentioned motor??
Is there any coding involved or it's just connections? "
Hello everyone I am planning to connect a 12v dc motor with the pixhawk and rotate the motor clockwise and anticlockwise. with my taranis plus transmitter is that possible ? if any one have an idea how to do it please let me know.The idea is to use…
"Thank you Bill , it works now;)"
Hello everyone I am new to this field and I would like to ask about the right platform that could be used according to the devices I am using:I am using a OSXPIXHAWKTaranis plus transmitter X8R receiverand trying to arm a Hexa copterWhat's better to…
guys I need help with my taranis setting The yaw is in the pitch and the pitch in the yaw location!!how can I switch between the two?
Hey everyone I am using APM Planner 2.0 and I didnt know whats 3D accelerometer calibration!!How to configure my Pixhawk ? with this method (3D accelerometer calibration!!)In the previous versions I see come commands like:turn the vehicle to the…
"Thank for the reply
I changed all of my ESR and the receiver but still I couldnt calibrate my PIXHAWK.
I think it's some of the IO in the PIXHAWK that burned.
How could I fix it ? or do I need to get a new one?"
I changed all of my ESR and the receiver but still I couldnt calibrate my PIXHAWK.
I think it's some of the IO in the PIXHAWK that burned.
How could I fix it ? or do I need to get a new one?"
Guys I need help I am using a Pixhawk , a X8R receiver and a taranis transmitter.I am trying to configure my Pixhawk but when I reach to the Accelerometer Calibration I click on the calibrate button I don't see the instruction line which says Place…
