About

Gender

Male


Location

Brookeville, MD


About Me:

hacker... maker... dad...


Please tell us a bit about your UAV interest

Quads!


Hometown:

Exeter


Activity Feed

rileyporter posted a discussion
Hey guys,  I am in need of your input.  Can anyone recommend a good quad / octo rotor 8ch or 9ch radio receiver combo?  I need to get one right away and figured I would reach out to the community for "what works". Riley
Oct 21, 2011
rileyporter posted a discussion
Reading the Sonar works for your altitude for <10 feet right?  After that the baro takes over.  In the APM I see that when I lift the quad over my head I still read like 1m or 0m.  Any thoughts on that?  In CLI mode it reads like 20cm to 80cm...…
Oct 17, 2011
rileyporter posted a discussion
Hey guys I am using the arducopter 2.0.48 release.  I have enabled the sonar in the APM planner hardware config.  I have booted into CLI mode and went to test >> sonar.  If the quad is on the ground I get 20cm.   When its more like 5cm.  I can lift…
Oct 14, 2011
rileyporter posted a discussion
Hello all.  I have my quad flying stable right now.  I am working on getting missions to work through the apm.  I click on the flight planner and set a "Take off" event to 10 (meters right?).I then have it land.  I write the way points to the quad.…
Oct 7, 2011
rileyporter replied to Mike W.'s discussion First Flights - Quad Flipping
"Its working now.  What I would do if I were you is look at the telemetry data with a ground control station.  If you are level on the computer and its pulling that way then there really are only a few things it could be.  
 
1.  Get eye level (make…"
Oct 4, 2011
rileyporter posted a discussion
Just wanted you guys to know that I finally got it to hover a bit today.  Putting some finishing touches on "little boy" and its should be ready to go. Thanks everyone who helped me out! Here is it's first real flight. Riley
Sep 27, 2011
rileyporter posted a discussion
I looked in the manual about the beep codes.  However this one was not listed.  Can you guys take look at the video and tell me what you think?  There is definitely a problem with that motor while running (during tethered and hand testing it seems…
Sep 26, 2011
rileyporter posted a discussion
Hey guys,  I made a video that explains what is going on. You can see it below.  Be warned that its loud.  VIDEO EXPLAINATION:TEXT VERSON:Basically what is happeneing is I have my quad tethered to a stand with some rubber cords.  When I take off the…
Sep 22, 2011
rileyporter replied to rileyporter's discussion Manual Mode? How to? Startup sequence?
"Stupid question?  Do I have to use a Magnetometer?  With quads?  I bought the oilpan thinking it had everything I needed... Is this not the case?
 
Riley"
Sep 22, 2011
rileyporter posted a discussion
Perhaps I am missing something big here.  I have I think pretty much everything working on my quadcopter.  I can read all inputs on it from the R/C.  My mode switch works... Currently it switches from ACRO, STABILIZE and SIMPLE.  My process is the…
Sep 21, 2011
rileyporter posted a discussion
I recently got my arducopter assembled and all hooked up.  When I go to calibrate my RC through the APM I get readings on everything BUT the throttle.  Not sure why?  I hook up a servo to that input on the receiver and it works just fine?  Any…
Sep 20, 2011
rileyporter posted a discussion
I got the DIY Drones APM Oilpan and telemetry kit yesturday.  I can get the APM talking to the ground station NP.  I hook up the xbee to the oilpan (correctly) and then connect my other xbee to the usb-xbee board I got from the kit.  When I hookup…
Sep 14, 2011