Gender
Male
About
Please tell us a bit about your UAV interest
robotics
Hometown:
chania
Activity Feed
Hi,I've setup a skywalker x8 with apm plane 3.4 tuned it and flies beautifully. Trying to achieve and test some features in gliding flight (throttle 0) I've noticed that the prop is free wheeling even at zero throttle and ESC motor brake enabled. I…
"Had the same issues with dji 30a optos not starting all together etc..once spooled up everything ok....still didn't like that and I flashed them with the blheli. Now I can calibrate, set them up with various settings and the copter flies better."
"Reading through the post and thereafter the comments, I see that there might be something that's missed and is related to the CG of the frame.
For example I have a 500 spider quad which is loaded and unloaded with stuff frequently, i.e. gimbal for…"
For example I have a 500 spider quad which is loaded and unloaded with stuff frequently, i.e. gimbal for…"
"Hey guys,
A little update on this thread.
It seems that I resolved the problem with all the quad funny angles,,,taking Spencer's suggestion below and Ricardo's from another thread, I tested the quad and paid careful attention to what it was doing,…"
A little update on this thread.
It seems that I resolved the problem with all the quad funny angles,,,taking Spencer's suggestion below and Ricardo's from another thread, I tested the quad and paid careful attention to what it was doing,…"
"Hey guys,
A little update on this thread.
It seems that I resolved the problem with all the quad funny angles,,,taking Ricardo's suggestion below, I tested the quad and paid careful attention to what it was doing, especially when yaw input was…"
A little update on this thread.
It seems that I resolved the problem with all the quad funny angles,,,taking Ricardo's suggestion below, I tested the quad and paid careful attention to what it was doing, especially when yaw input was…"
"Hi Justin,
even though the wiki states to ignore opto djis calibration, i did the process anyway. the motor orientation, spin direction and wiring are alright; nothing there...
still the same behaviour."
even though the wiki states to ignore opto djis calibration, i did the process anyway. the motor orientation, spin direction and wiring are alright; nothing there...
still the same behaviour."
"Hey Mike,
I tried to keep in the air to try to figure out what's going on. .also tried auto tune but nothing there...
it seems the problem occurs after yaw input and/or some degrees of yaw rotation. Funny thing is that if I put it on the ground and…"
I tried to keep in the air to try to figure out what's going on. .also tried auto tune but nothing there...
it seems the problem occurs after yaw input and/or some degrees of yaw rotation. Funny thing is that if I put it on the ground and…"
"OK, here is the log...
I also calibrated the ESCs again..no improvement.
I think next time I'm just gonna let the thing fly to the wall...2015-05-29 19-39-31.log"
I also calibrated the ESCs again..no improvement.
I think next time I'm just gonna let the thing fly to the wall...2015-05-29 19-39-31.log"
"Hi Spencer,
No, simple and super simple are disabled.
The quad will take input but at that point I have to figure out which way to move to stick to bring it back. .. it even seems that the inputs are rotating as time passes...I.e. while im pitching…"
No, simple and super simple are disabled.
The quad will take input but at that point I have to figure out which way to move to stick to bring it back. .. it even seems that the inputs are rotating as time passes...I.e. while im pitching…"
"Hi Mike,
Thanx for your response.
Unfortunately for me no, that is not the case. The motors are wired up correctly and the mixes are alright; just the ones required for the flight modes...
Further the quad seems to fly ok in the beginning and then…"
Thanx for your response.
Unfortunately for me no, that is not the case. The motors are wired up correctly and the mixes are alright; just the ones required for the flight modes...
Further the quad seems to fly ok in the beginning and then…"
Hi guys,I'm just starting with APM and this probably could well be my first post here. So, a heartily welcome :)On to the issue....Prior to the APM setup the copter was running a naza lite with no issues at all; eventually I got bored of it and…
Hi guys,I'm just starting with APM and this probably could well be my first post here. So, a heartily welcome :)On to the issue....Prior to the APM setup the copter was running a naza lite with no issues at all; eventually I got bored of it and…
