Comments

• 

  Trent at MyGeekShow August 3, 2013 at 9:40am

  @Carloss84: To see the parameter list you have to have an APM connected via USB or Telemetry. I've seen the hardware list view not load properly if I didn't have an internet connection. Try those and see if it works for you.
• 

  Carloss84 August 3, 2013 at 9:35am

  Hi, having problems using mission planner, it worked fine before, but haven't used it for a few months and now when I click on the config tab and go to params nothing appears ? also advanced params ? and theres no firmware for any vehicle , I tried to update on help and it came up with a error and couldn't update ?. So unistalled the old software and installed the new 6.12 I think it is ,and couldn't get it to open mission planner ? it also came up with a error so had to restore my computer to get the old one back as then atleast I can use mission planner . any help please ? cheers. the old version im using is 1.2.3.6 mav 1.0.
• Serg Abad July 3, 2013 at 1:52am

  Hi guys,

  Can anyone point me to the specs and wiring directions/instructions of the 3DR servomux board? The board is no longer in the store and a search on the new forum returns nothing.  

  Thanks in advance. 
• 

  Gustav Kuhn April 13, 2013 at 11:14pm

  Hi group,

  I'm quite close to flying with APM in Big Ugly

  http://diydrones.com/profiles/blogs/drastik-50cc-build-log

  I attach some logs of two ground runs, the vibration doesn't look too scary, then, what do I know ?

  Regards

  2013-04-13%2015-58-09.tlog

  2013-04-13%2015-40-31.tlog
• 

  leopoldo ojea April 9, 2013 at 8:05am

  done. Thank you bill
• Developer

  Bill Bonney April 9, 2013 at 7:49am

  @leopoldo: Could you raise your question as a forum post as it's easier to comment  on that post. (see Add a discussions" button above left of this post :-) )
• 

  leopoldo ojea April 9, 2013 at 3:57am

  Hello all, 

  I need your feedback and help, yesterday I was flying my airplane with APM 2.0 I saw in OSD that it changed to Circle mode, that was probably because a low Tx or Rx low signal.

   Since I noticed the mode change I move the switch and put in RTL mode. OSD show me that it was in RTL but later when the airplane was coming back it changed to circle mode itself. So I had to put in manual mode and flew it back to home as I could.

   I did other test and it happened two or three times more.

  Each time that switch to RTL mode meanwhile the airplane was coming back it change to circle mode alone.

   

  This sound real strange for me because I understand that when you change to RTL mode it has not change  the mode until you move the switch.

   Could you please help me understanding why this could be happened, in this condition the RTL mode is not reliable.
• Garry McLeary March 27, 2013 at 4:38pm

  Hello all, I am not sure this is the right place to be asking basic questions, but here goes:

  I am using xplane 9.7 with mission planner 1.2.35 mav1.0 to get started flying using the sim. I am able to fly the plane in xplane, but the only mode that works is the manual. If I switch to other modes, I can see that planner switched to the mode I switched to, but the the plane doesnt stabilize and I can still control the pane as if i am in manual mode. Any ideas what I am doing wrong?

  The other strange thing is I am only able to calibrate the radio and fly the plane using the ArduPlane V2.70 instead of ArduPlane V2.70 HIL. If I upload the HIL version there is no communication between my radio and the planner. How do I get the radio to respond in HIL mode? I am wondering if this is why it doesnt work when I switch to stabilize mode.

  Thanks
• 

  Ric Lecoq March 12, 2013 at 12:47pm

  I don't know if there's the right place to post but i try... How could i help by translating Arduplane Wiki in French ? You probably know that the French guys are a bit lazy and have great difficulty even with google translate !!!
• 

  Dave Schilling March 5, 2013 at 6:09pm

  Thanks Stephen Gloor will check ot the DraftSight. Been down for a couple weeks had a hip replacement.