I know that I2C splitter can accept digital sensors like Airspeed ,, Compass , GPS , Leds , USB
I need to add RPM Sensor to pixhawk , Can I use I2C for that ?
Dose the I2C accept any digital Data ? OR just special Sensors ?
My problem is that I need to
Read more…Hi,
I want to adjust cruise speed.
At default settings I have a ground speed of about 42km/h (without airspeed sensor), and I think the optimal speed should be lower. In the mission planner I have value "Cruise speed", default 12m/s. I updated it to 9.
Read more…I'm currently building a Talon (v3), mainly waiting for parts.
While looking for high capacity batteries I found out two things; There are a lot of brands, and prices are still steep in the high-cap regions.
I've also seen a few people on the Tube usin
Read more…Hi I have been setting up 2 quad planes, pretty standard setups...flying wing with 4 vtol motors and a rear mounted pusher motor. Both builds wich are on different firmware versions have reversed pitch in quad mode but correct pitch and pitch stabili
Read more…Hi guys,
I have a Pixhawk from Radiolink and always in every first attempt of armed I get the error "PreArm: Gyro Inconsistent".
The most strange thing is that i'm using only the external gyro+compass. i disabled the internal to avoid this issue. Also
Read more…Hello, I'm new to ArduPilot, but not to computing or open source. I'm working with a group building a tailsitter with a single pair of props for both hover and horizontal cruise. (For type of VTOL, think Ryan X-13 or Martin V-BAT.)
We were going to
Read more…I've seen a few videos and tales of multi-rotors and planes falling from the sky "flip of death" and such. They are all very old but I'm wondering if that sort of thing still happens.
Read more…I'm new to Arduplane, but I've got high-mileage left-handed reflexes, and need mode 3 to fly. But neither of the ground stations I've tried allow for that control layout. How can I configure Mission planner or Qgroundcontrol in stick mode 3?
Read more…hi everyone, I am building a quadcopter with pixhawk that will be able to deliver stuffs(like pizza), I am done with the entire frame with wood but I am haven a little challenges in the creation of the payload. Can anyone help. Thanks
Read more…I just installed 3.8 on a pixhawk without AS sensor and was surprised to find that Airspeed (synthetic since I have no sensor) was not being reported over Mavlink to my OSD....I am pretty sure that on a 3.4 APM system I had, it was being reported and
Read more…Background: We've got a large scale powered glider that has been flying pretty well, except for one thing that is baffling. We've done Autotune, setup and checked each parameter carefully in the list and wondering if we potentially missed somethin
Read more…Hi,
From reading various threads about people being confused about getting no throttle in AUTO while on the ground I understand that ArduPlane will not give you any throttle in the Auto modes while it thinks it's not in flight.
My question is how does
Read more…How to install Benewake TF SERIES on PixHawk
（Take TF01 for example）
Install TF SERIES module on your drone vertically to the ground so you can get the absolute altitude of your drone. Here is how to install our module on PixHawk. We provided two met
Read more…I understand that APM is no longer supported, but my 2.78b system was flying great on my miniTalon on an APM FC....
but then I had to replace the FC when it was destroyed accidentally when installing some new lighting on the plane ....and I find now t
Read more…No servo output on S1, S2 for elevons.
Servos work great connected directly to Rx.
APM Planner shows artificial horrizon and compass. Radio calibration looks OK.
Problem is, no output signal.
Is this a defective flight controller?
Any trouble shooting ad
Read more…I have been flying my APM miniTalon succesfully for a long time on AP3.0.1....recently I had to replace the APM and reflash....unfortunately, MP will only load 3.4 firmware....the problem is that with this firmware MAG_ENABLE is not longer maintained
Read more…Hello All,
Someone could help me, i can't manage to make the RC6 as a release parachute on Pixracer and Arduplane 3.7.1???
I'd configure the channel 7 on my taranis and in MP in order to released parachute, it's seems working as when i arm the plane an
Read more…Hello people.
I need your help please.
Today I tested a recently built fixed wing frame, the Skywalker 1900 build for a course in Argentina to teach people about UAVs and make them fly legal. I am using an APM 2.5 with GPS and no airspeed sensor (yet).
Read more…Hello everyone,
I'm trying to setup the loss of RC comms with my RMILEC long range system (LRS). Basically, there are 2 modes you can choose from (custom servos and channel positions or hold last servos positions). The system works by sending regular
Read more…I try to setup servo gimbal with mission planner . i Connect servo to RC10 & RC11 but i can't check “Stabilise” box.
servos start jiggling and jerking and overheat
Any help would be great!
Read more…