Hi all ,
I am try to use flightgear simulation with MP to simulate my flight ,
maybe this way will allow me to solve problems I faced.
Compenents :
Mission planner v.1.3.32
Flightgear v.2.10.0.3
Pix FMU+IO (china pixhawk ) also ( APM 2.5 )
I followed by th
Read more…This is my initial build of a fixed-wing with APM 2.6. I power on in Manual mode, and as soon as APM initializes, the motor/prop spins. Throttle responds to input like it's already armed (it's not) and it will not go below about 10% power?! ESC is
Read more…Hi again ,
I am still having problem in Auto modes using Pixhack FC
My Question is
What's the different between ( Absolute , Relative , Terrain ) Altitude in Mission planner ?
Whats is the function of the check box ( verify Height ) ?
also in the right si
Read more…Hi All ,
Hardware:
- Flight controller : PIXHACK
- GPS Ublox
- MiniOSD
Software:
- GCS : Mission Planner.
- Firmware : Arduplane 3.4
Problem:
After previous tests and posted topics here I solve the problem of pitch
Read more…Hi - hoping for some help here. I did post this in the Pixhawk user group but no reply.
I am using my Pixhawk in a fairly complex fixed wing mapping drone and I need to free up some channels for some added functionality. Basically I am using Aux3/RC11
Read more…For our UAV project we are using the Pixhawk and Mission Planner 1.3.34. During flight we'd like to adjust the airspeed of the UAV. We are in AUTO mode flying the waypoints and are using the "Change Airspeed" under the ACTIONS tab. However, the speed
Read more…Hi
Can someone please explain the interaction (if any) between TRIM_AIRSPD_CM and TRIM_THROTTLE? I know these parameters are unrelated, but is there a situation where they can both be trying to influence airspeed?
Presumably TRIM_AIRPSD_CM is more imp
Read more…Whenever my ESC is connect to Ch 3, I have no control, but if I move the ESC to any other Ch (1,2,4) it responds as expected.
I am using a Taranis Plus and X8R to Pixhawk via SBUS. Below are pictures of my RC_MAP and Taranis input and mixes. I tried c
Read more…Hi all , Come back again after test,
Hardware :
My Own plane , similar to Skywallker ,
Flight controller : Pixhack CUAV .
GPS : Ublux 7
other additional tools ,
Software :
Firmware : Arduplane 3.4
GCS : Mission Planner.
with out AirSpeed , throttle cruise 60
Read more…Hi all ,New Questions in this discussion will provide me with good knowledge . Hope find interest answers .actually I use Manual and Stab modes It works well for me , Need to try other modesFirst : How to use more than 3 mode in the flight ?and How t
Read more…hello all
I Hop to find real useful information and solutions .
Hardware:
-SkyWallker
- APM 2.6 ( also test with Pixhack )
- GPS ublox
- MiniOSD
-
Software:
- Mission planner 1.3.32
- Arduplane Firmware 3.4
I test the Auto mode in the flight but when I c
Read more…Hi All ,
I had many crashes with my plane
I am using Arduplane 2.6 and pixhack (Not pixhawk ) and both has the same problem .
When I change mode from stab to Auto the throttle is off and plane start loss altitude while heading to waypoing direction.
I d
Read more…I have flown APM since 2012 in my Quads/Hexs
I want to get a flying wing that I can use the Pixhawk with.
I want it to be able to take off in a park sized field, fly way points and auto land. (basic recon)
I assume we are at that point with arduplane b
Read more…Hi,
from
(https://www.faa.gov/uas/registration/)
"
If you own a drone, you must register it with the Federal Aviation Administration's Unmanned Aircraft System (UAS) registry. A federal law effective December 21, 2015 requires unmanned aircraft registr
I had a crash today caused by the loss of the RC transmitter signal. I was in a designated safe area and nothing bad happened except for the plane, but I am sure the crash could have been avoided if I had a deeper understanding on how to operate ardu
Read more…Hi all,
I have done de Auto calibration for the airspeed sensor on a Skywalker and the resulting value for the Ratio was 4.
I read the normal value should be between 1.5 and 3. Do you think i would have problems with that Ratio value?
I did the calibrat
Read more…hi folks,
i ve been running apm 1.0 ages ago, with a great pleasure.
now i am coming back with an apm 2.6 and i am facing an issue, that i dont understand at all.
when i power my plane in manual mode (i ve disable arming_require) everything works fine.
B
Hi guys!
In a plane you use the power module or attopilot to measure current and voltage of the main batteries.
In a plane the servo rails must be powered by it's own power source, and with the zenner diode, if the power module fails to provide power t
Hello all.
I would like to ask you, dear members of the arduplane forum, if the lenght, inner diameter and type of material of the air tube of the airspeed sensor matter in terms of affecting the precision of the sensor. I have searched all over the i
Hi all,
I flew my skywalker for the first time yesterday. Sometimes while flying, the message "bad compass health"appeared
I attach graphs of 2 logs, throttle and Mag_field. Is the magnetic interference razonable? I think it isn't, but I don't know the
Read more…