I was flying with a glider in FBWA mode, when from the movement of the aileronsRead more…
he did a spin.
I do not quite understand, because it's set to do at most 40% of roll.
Does anyone know how this could have happened?
Hug.
I am looking for the Aero M Camera Bay. I have performed an exhaustive search and before I design and print one I was wondering if anyone knows how to locate one? Or if there is a 3D file? (.stl) Any help would be great. Thank you.
Hello all,
I have been working on a VTOL modification for a couple of weeks now, and had just gotten to the point of conducting a few hover tests. The night before I went through and checked to make sure everything was properly functioning, and all wa
Read more…Hello guys! Me and my classmates are having a school project. We decided to build an arduplane using the XUAV Mini talon. I already have experience flying RC planes but too little experience about flying an arduplane. Our school requires us to do a d
Read more…Hi all ,
I see that the Arduplane and Pixhawk support the Parachute setting ,
I have Plane similar to skywallker and I need to setup Parachute . but I don't know where to start .
Can you help in where I can find suitable Parachute for my plane with weig
Read more…I recently did a few rounds of Autotune on both my X-5 and X-8 flying wings. All worked well and both planes seem to be flying well, however, when I checked the derived values after the Autotune flights, I noticed that RLL2SRV_D and PTCH2SRV_D values
Read more…Hi,I've got this weird problem and hope someone could help me with it.I'm trying to setup APM 2.5 on my Firstar v2 2000. It is a large and heavy plane and requires a lot of space to land as it needs to fly fast to stay in the air.I want to setup crow
Read more…I am planning to make a servo gimbal for my gopro on my Flying Wing, and I want to loiter around a point of interest, is DO_SET_ROI also available on the Plane firmware?
As far as I know only copters can do that, correct me if I'm wrong
Hi!
Do you guys have a suggestion what airplane should i build? Buying a kit is not an option. :( They want me to assemble one out of foamboard(Depron) which will carry APM 2.6, fpv camera and 2x 2200mah 3s battery. Thank you guys.
Read more…Hi all,
I'm having and issue with a power module and Pixhawk.
I just can't calibrate the voltage sensor, I read the Lipo voltage with a multimeter, then input that value in Mission Planner but the values go crazy.
I tried "Other" and all the options in
Read more…Hi all ,
I need to hack Camera go pro to control throw pixhawk
I remove the power switch cover of the camera and connect it with two wires ( when connect them together ) for 3 second the camera ON when do it again the camera of .
Now Can I connect them
Read more…With the recent adding of X-Plane as simulation backend in the SITL functionalities of ArduPilot (http://ardupilot.org/dev/docs/sitl-with-xplane.html), I felt useful to design some UAV models.
Here are two different models with their Mission Planner p
Read more…I’ve made some good progress on getting my Observer/Ranger-Ex Quadplane dialed in. I’ve done 4 transition flights and about 20 hover tests and, whilst it is much better after adjusting some of the parameters, I’m still wondering if it could be a litt
Read more…My Quadplane is all ready to go (pic attached) but I have 2 questions I’m hoping someone can help me with. I have done 3 fixed wing Pixhawk planes, so familiar with Plane firmware, but my multirotor experience is limited to DJI products thus far.
Fir
Read more…I have this
http://www.getfpv.com/lumenier-ce-720-effio-v-720tvl-super-wdr-camera.html
and this
The cables that came with them a
Read more…I have a question regarding calibration, hoping someone can give some steer:
After initial flights have been conducted in manual mode to baseline a plane, should it not be necessary to recalibrate the controls such that the PWM trim value is right for
Read more…I attempted a mission.
Arduplane is set to continue on tranmitter failsafe. After takeoff I turned off the transmitter. I had a telemetry connection. I have flown many flights in the hard config of this plane so i am very positive that the video is no
Read more…Hi all ,
Can I pass the GPS information maybe( NMEA ) to Google earth software in real time and flow the path in google map ?
maybe in the temp window of mission planner ( Ctrl+F) there are some thing about GPS like
GPS inject ?
MAV Serial Pass ?
for what
Guys,
does anybody is using Pixhawk for controlling Canon/CHDK camera via GentwireUSB2 cable? I have a plane with Pixhawk and I want to control camera shutter by one channel and lens open/close by second one. When Im trying to control it via Gentwire
Read more…Hi all
Is it possible in Arduplane to set the Geofence as it is set in Arducopter so it can be used as a safety feature, to protect against loss of orientation etc as set as always on like it can in copter.
All I can find is a bizzar option where it ha
Read more…