About

Gender

Male


Location

São Paulo


Please tell us a bit about your UAV interest

All about FPV, 3dr Pixhawk, Fatshark Dominator HD and quadcopter.


Hometown:

São José do Rio Preto


Activity Feed

Grazziani Resende replied to Sean Whitney's discussion Pixhawk Wiring
"I forgot the parameter

trex450.param"
Jul 20, 2017
Grazziani Resende replied to Sean Whitney's discussion Pixhawk Wiring
"Hello, Sean, first of all, congratulations on the setup in your helicopter. I'm trying to set up my helicopter and I'm doing the same with your H1 configuration  function of the tx and puted the sequences you put in, but I'm not having success in…"
Jul 20, 2017
Grazziani Resende replied to Grazziani Resende's discussion Roll problem with FBWA mode. in ArduPlane User Group
"Hello, it makes all sense what you wrote. I just got to see it now. Before he turned, he was very slow.

Thank you very much! Mossbackfarm said:
Without a dataflash log, I can't tell for sure, but when you hit RTL, you had some compass and EKF/POS…"
Mar 1, 2017
Grazziani Resende replied to Grazziani Resende's discussion Roll problem with FBWA mode. in ArduPlane User Group
"Yes, you understood everything right. I did the motion compensation tests successfully. My question is: When I use the radio control stick to left position in FBWA mode, should it stop at 40% or will it continue turn up until the stick return to…"
Feb 28, 2017
Grazziani Resende replied to Grazziani Resende's discussion Roll problem with FBWA mode. in ArduPlane User Group
"What happened is that in FBWA mode he managed to exceed 40% and was upside down. Should not the pixhawk block this movement?
Nobel0 said:
Hello Grazziani,

Excuse me if i got this wrong, did you mean the glider made a spin after you give ailerons?…"
Feb 28, 2017
Grazziani Resende posted a discussion in ArduPlane User Group
I was flying with a glider in FBWA mode, when from the movement of the ailerons he did a spin. I do not quite understand, because it's set to do at most 40% of roll. Does anyone know how this could have happened? Hug.
Feb 28, 2017
Grazziani Resende posted a discussion
Hello, I'm having problems when I'm putting the photos and the location.tx file in the software to generate the mosaic. As you can see in the attached photo, everything is disorganized, someone has already gone through it and can you help me? I…
Feb 7, 2017
Grazziani Resende posted a discussion
Hello, I have problem with my plane, when I change to auto mode. He goes to right direction, but I used DO_CHANGE_SPEED to 12m/s and nothing change, the airplane flying about 18 to 25m/s.Do you know about this problem?Hugs
Aug 4, 2016
Grazziani Resende posted a discussion
  Hello , I'm having a problem with my Pixhawk .   I'm using 3.0.1 firmware for airplane , stabilize and RTL mode, are working perfectly , but when I make a flight plan to automatic mode , the plane simply flies straight and if let you go, it lose…
Mar 7, 2016
Grazziani Resende replied to Thomas Mueller's discussion Problems / Error message when Linking Futaba T14SG to Pixhawk with R7008SB
"I have same Thomas problem.
The pixhawk recognize the Futaba SBUS and when I turn On the Radio, the receptor light turn Green (linked), but the QGroundControl not recognize the radio linked on software. Understood?
If I apply Mission Planner…"
Feb 12, 2016
Grazziani Resende replied to Grazziani Resende's discussion How to fix Pixhawk with 6s lipo battery and showing difference of volts of real battery voltage?
"Hello, I determined with multimeter to get real voltage and I compared with OSD screen information. I modified 3dr module with 2s-8s UBEC. I need know where in Mission Planer, I can change the voltage parameter to modify battery low alarm.
I don't…"
Aug 2, 2015
Grazziani Resende replied to Grazziani Resende's discussion MinimOsd is not showing information on the screen
"Hi, I solved my problem with this video, (see after 10:05 minutes of video):
https://www.youtube.com/watch?v=z1xM_m-ur5c
It's in portuguese language, but have video demonstration, very easy to understand or access this site:…"
Jul 29, 2015
Grazziani Resende posted a discussion
   Hello , I set one up Pixhawk to accept 6s battery and is flying perfectly, but the OSD screen is showing a difference of 0.8 volts the actual voltage of the battery , so the battery alarm is triggering before the flight time they could get . …
Jul 29, 2015
Grazziani Resende replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD
"Exploded resolution"
May 24, 2015
Grazziani Resende posted a discussion
   Hello , I have problems with minimosd information. When I turn on the Pixhawk the minimosd information appears on my screen Fatshark , but without information, all can see is number zero.  I plugged the minimosd in Telemetry port 2 and Telemetry…
May 24, 2015
Grazziani Resende replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD
"Hello , I'm having the same problem of image expansion with minimosd , but in my case I have not used the voltage 12v , I did the soldering in minimosd to use the voltage Pixhawk . I tried a bit of everything still did not get hit with the OSD…"
May 23, 2015
More…