About

About Me:

student and I like hoobe flying


Please tell us a bit about your UAV interest

i like flying


Hometown:

London


Activity Feed

Abolo replied to Abolo's discussion RC plane Parachute tool and configuration in ArduPlane User Group
"@Brian Christal
it's nice parachute but I think it couldn't fit with my fix-wing aircraft ,,
Dose there any type for fix-wing ( mean can fit within the wing area ?

Regards .."
Nov 21, 2016
Abolo replied to Abolo's discussion RC plane Parachute tool and configuration in ArduPlane User Group
"Brian Christal said:
This documentation should get you started: http://www.tuffwing.com/support/UAV_Mapper_Parachute_Installation.html
This might get it down in one piece: http://www.marsparachutes.com/mars-58/

-Brian




Thanks for the urls , I…"
Nov 7, 2016
Abolo posted a discussion in ArduPlane User Group
Hi all ,I see that the Arduplane and Pixhawk support the Parachute setting ,I have Plane similar to skywallker and I need to setup Parachute . but I don't know where to start .Can you help in where I can find suitable Parachute for my plane with…
Nov 6, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"Very good
I have to do two separate function
1- power on camera
2- start record ,
I will use two switches as shown in replays .
Now one step done with trigger ,with RC5
How can I assign the second function ?
How to do another output throw the RC7 ,…"
Aug 10, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"I used rc5 as camera trigger and test it from the plane page I works fine , ( I will use this for shatter )

Now I need to Do that command throw waypoint command
Second I need another way to output another signal for powerOn the camera also doing…"
Aug 9, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"this relay now not for shutter it's for power the camera on ,
I will duplicate with another relay for camera shutter , 

using camera trigger will out the needed signal ?
Do you mean I don't have to plane it with mission command ?

Regards,"
Aug 9, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"no actually I expect output as do set servo command !! mike de leon said:
idk about the kill switch how it works, base on your layout its correct, it should trigger the relay if ever 5v is send by the kill switch, did you go to mission…"
Aug 9, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"thanks all for helping with good information

I just get rcexl opto gas engine kill switch v2.0
which use for cut off the engine pdf manual
I use it with the receiver X8R and connect it to relay (Meisei m4-5h) and it works fine and the relay work…"
Aug 8, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"naish said:
@ Abolo
No you won't damage the Gopro, but you will damage the pixhawk as a relay will use more than the allowed 15mA you can get from the I/O pins. 
You have to use a solid state realy like…"
Aug 6, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in ArduPlane User Group
"I already open the Gopro and get out two wires for power switch just need to connect it to relay to operate throw Pixhawk
The camera has it's own power throw it's battery ,
the relay function is just switch to close for 3 second and release ."
Aug 6, 2016
Abolo posted a discussion in ArduPlane User Group
Hi all ,I need to hack Camera go pro to control throw pixhawkI remove the power switch cover of the camera and connect it with two wires ( when connect them together ) for 3 second the camera ON when do it again the camera of .Now Can I connect them…
Aug 4, 2016
Abolo replied to Abolo's discussion Mission planner GPS passthrough to Google earth? in ArduPlane User Group
"@MichaelOborne

Thanks a lot , I get the NMEA data out to google earth ,

Regards ,"
May 15, 2016
Abolo posted a discussion in ArduPlane User Group
Hi all ,Can I pass the GPS information maybe( NMEA ) to Google earth software in real time and flow the path in google map ?maybe in the temp window of mission planner ( Ctrl+F) there are some thing about GPS likeGPS inject ?MAV Serial Pass ?for…
May 14, 2016
Abolo posted a discussion in ArduPlane User Group
Hi all ,I am using telemetry 9xtend900 mhz to send and receive pixhawk data , and I am using Video throw video transmitter .now I have information to send such as :Sensor dataCamera control dataGimbal controlthat data doesn't work with Pixhawk So I…
Apr 7, 2016
Abolo replied to Abolo's discussion how to connect G-3D Gimbal with pixhawk ?!!
":( why their is no replay , I don;t know if there is another place to post ..

waiting .."
Mar 31, 2016
Abolo posted a discussion
Hello all ,I have G-3D Gimbal controller from walkera and I want to attach it with pixhawk ( actually its chines pixhawk called pixhack ) but it's similar to pixhawk . I tried to connect the wires from the gimbal to pixhawk put when I power the…
Mar 30, 2016
More…