Gender
Male
About
About Me:
I'm a Surveyor
Please tell us a bit about your UAV interest
I'm interested in aereal photogrammetry, using UAVs
Hometown:
LP
Activity Feed
"Paul, I had a similar problem. Couldn´t make it work with my notebook (an old notebook). I tried then with Tower app on my Android phone and it worked well, so the DL Bluethoot was OK, it was a problem with the notebook bluetooth.
Now I have a…"
Now I have a…"
"Yes Mike,
I did some more tests. I measured de voltage between ground and PIN 2 in the Power Module. It has to be a value that multiplied by 10.1 (or so) gives the Lipo Voltage. Well, it doesn't, it gives a very diferent value.
-Voltage between…"
I did some more tests. I measured de voltage between ground and PIN 2 in the Power Module. It has to be a value that multiplied by 10.1 (or so) gives the Lipo Voltage. Well, it doesn't, it gives a very diferent value.
-Voltage between…"
"Thanks Hein, I'll verify that."
Hi all, I'm having and issue with a power module and Pixhawk.I just can't calibrate the voltage sensor, I read the Lipo voltage with a multimeter, then input that value in Mission Planner but the values go crazy.I tried "Other" and all the options…
Hola gente del grupo,Alguien sabe si existe alguna relación entre la resolución GSD y la equidistancia entre curvas de nivel que puedan generarse? Por ejemplo si quisiera generar curvas cada 0.50m qué GSD máximo recomendable usar?El terreno de…
Hi all, I recently bought a custom hexacopter, made of carbon and size 800mm. It flied well 6 or 7 times.Today I was flying in Loiter (with Pixhawk) and suddenly saw some smoke and the hexa began to go down. When I reached the place I saw one motor…
"Thanks, very well explained. Do you know if the data link works with the APM too? Or only with Pixhawk?"
"Gracias Leandro y Jordi"
Hola gente del grupo,Tengo un Skywalker con una Canon y lo he probado en distancias no muy grandes y funciona bien.Ahora tengo ganas de probar con un mayor alcance de telemetría con APM. Vi por internet varias opciones, ahora salió el Dragonlink V3…
"Hi Grant,
I ordered an USBasp Avr Programmer to try to flash the APM boot loader. Tomorrow I would have it.
Let's see if it works.
Thanks.
Max"
I ordered an USBasp Avr Programmer to try to flash the APM boot loader. Tomorrow I would have it.
Let's see if it works.
Thanks.
Max"
Hi all,I am having problems with my board. It was OK and I was flying perfectly my plane until yesterday, when I tried to upload the latest firmware 3.4 and when it was about to finish, the message "Upload succeeded but verify failed: exp C got 14…
"Thanks Bruce and Andrew.
I tried with another speed sensor and the results were the same. A value of 4 with Autocal.
Now I'm waiting a new pitot tube to try. "
I tried with another speed sensor and the results were the same. A value of 4 with Autocal.
Now I'm waiting a new pitot tube to try. "
"It was the telemetry. It was close the APM and the GPS and seemed to cause the interference.
Now I put it far away and no more "bad compass health" problems!"
Now I put it far away and no more "bad compass health" problems!"
Hi all,I have done de Auto calibration for the airspeed sensor on a Skywalker and the resulting value for the Ratio was 4.I read the normal value should be between 1.5 and 3. Do you think i would have problems with that Ratio value?I did the…
"Thanks Adam and Grant,
I will read those pages."
I will read those pages."
Hi all,I flew my skywalker for the first time yesterday. Sometimes while flying, the message "bad compass health"appearedI attach graphs of 2 logs, throttle and Mag_field. Is the magnetic interference razonable? I think it isn't, but I don't know…
