Comments

• 

  Richard Kennedy December 8, 2015 at 11:32am

  I believe this is correct. Nothing worse than having an issue or blown component for something silly... been there done that. Not sure the best place to post so I put it here. It wouldn't show up in a search so maybe a new topic is better.

  
• 

  Richard Kennedy December 8, 2015 at 11:27am

  I'm almost certain this very commonly found pinout of the pixhawk is incorrect FYI

  
• James tate December 4, 2015 at 6:56am

  The RC port should not be used for telemetry.

  The RC port is used for SBUS, PPM signals , it is a IN port not a OUT port.
• 3qs7z40lxxok2 December 3, 2015 at 9:31pm

  i all been browsing for days and cant fine a answer 

  on the pixhawk is it ok to pull 5V 175 mAh of the RC port to drive a telemetry receiver  

  on full load up to 200mAh
• Michael Berthelot December 1, 2015 at 4:15am

  I had a PIXHAWK  flyaway few months back , crashed into a tree ,no damage , However , we had no control at all. RTH and geofence and all other fail. to respond . I have the sd card ready to upload files to the site here if any one wants to figure what went wrong

  What files do I upload,, all ?

  Thanks Michael
• Phil Horner November 22, 2015 at 10:09pm

  Just a bit of an update on my gps issues. The maps supplied in Mission planner are giving different readings to Google Earth Pro. It is the maps or the set up of those maps in Mission Planner that appears to be the problem. Can the maps list in mission planner be updated or the setting altered to correct this discrepancy?
• Phil Horner November 22, 2015 at 5:25pm

  Well, finally the weather has broken and I've just returned from the field after trying to sort out the GPS discrepancy I'm getting between my iPhone and my Pixhawk drones. Nothing has changed, so it doesn't appear to be the likes of multipathing. I've just dug the hole I'm in even deeper because I've just updated Missionplanner and I see a whole lot more features than were there before, and I now can't make head or tails out of the limited ability I had when it comes to reading logs. Would someone be so kind as to have a look at the last logs I've downloaded? Apart from the gps issues, I'm also concerned about the vibration level. It used to be almost perfect but I've just added some landing skids and I think they may be amplifying the small vibes I had.

  https://www.dropbox.com/s/gclepuxj32ax5oz/2015-11-23%2011-04-40.tlo...

  https://www.dropbox.com/s/tj0379yiz4zintx/2015-11-23%2011-09-43.bin...

  I've now got to get to grips with what SBAS is so I can make alterations there if required.

  

  Dropbox - Link not found

  Dropbox is a free service that lets you bring your photos, docs, and videos anywhere and share them easily. Never email yourself a file again!
• stefan jakobsson November 15, 2015 at 9:29am

  Yes that solves it! Thank you all  for the help!
• stefan jakobsson November 15, 2015 at 9:20am

  Thank's for fast replies! I run the "git clone https://github.com/diydrones/ardupilot.git" command and after that I run the git checkout Copter-3.3.1 command but it did not work.I get this message: fatal: Not a git repository (or any of the parent directories): .git       
  
  
• Developer

  Bill Bonney November 15, 2015 at 9:07am

  git checkout Copter-3.3 will put you on the right branch. git checkout Copter-3.3.1 checks out the tag for the release in detached head mode, which is a little confusing. It is the exact state of the repo when the release was made when you check out the tag though