CrossFire=Pixhawk 2.1
Hi can some one please tell me if it is going to be implemented that we can use CRSF protocol with the pixhawk please,many thank's,Marty
Read more…
1 Reply
All Discussions (17288)
Sort by
Electronics Engineer wanted for Pixhawk 2 Carrier Board etc
We are seeking an Electronic engineer / undergraduate, to develop an autopilot carrier board for a drone, and a set of sensor interfaces.
The suitable candidate will need to have the following:
Good knowledge of Altium
Have his own copy of Altium
Read more…Geotagging images with GeoSetter
I've been experimenting with GeoSetter to geotag imagery taken from an M600.
Is anyone using this software?
I've been able to sync photos with telemetry data in gpx format using the "Use track point from map" option. The issue I'm having now that I h
Remove waypoints from HUD as they are reached
Is there a way in mission planner to have waypoints that are reached by a uav be removed from the the HUD as they are reached so they don't clutter the screen?
Read more…What is The Smallest ArduCopter Capable Flight Controller
What is the smallest ArduCopter capable flight controller?
Read more…ardupilot breakdown?? (first edit : 2017-09-07 / 20:00)
hi, all
I'm making Rover.
But I think there's a problem with the ardupilot mega 2560 board.
When you connect the USB, the green LED and the red LED are fixed and the blue LEDs are turned off.
Device Manager " Unknown USB Device (Device descriptor request
Read more…Heading hold in manual?
Hey Guys, I am playing with a Wild Thumper 6x6 setup as an ArduRover. I am not so much interested in it being setup for autonomous usage but want to tune the manual operation. Is there a mode or setting I can adjust so that it has heading hold when d
Read more…ArduPlane 3.8.1 Issue
Hello all. I have been flying a Pixhawk 2 board in a delta wing with AP 3.8.1 . I have been running mission planner 1.3.49.
After Upgrading firmware from 3.7.1 to 3.8.1 the throttle does not work in all automated flight modes (AutoTKOFF, AUTO, FBWB, F
Read more…APM Planner Flight Data Page - Tx Does Not Change Flight Modes
PixRacer Flight Controller: Everything seems OK on the APM Planner2 Transmitter Calibration page. 3 Flight Modes set up and PWM values recorded using the Tx Flight Mode switch. On APM Planner's "Flight Data" tab I can set the flight mode - but only w
Read more…Is This a Universal Propeller
I'm crowdfunding for my new universal propeller, sectional nozzle propeller aka beetle elytra propeller after being granted 20 years patent NG/P/2016/417 by the Nigeria Patent office via the following weblink.
https://www.indiegogo.com/projects/world-
Read more…Data encryption and suitable frame
HiHow to encrypt the data link communication and control between drone and the ground station"tablet, pc, etc... " and what is the suitable quad frame that can carry 24.5 up to 27 inches props?
Read more…SITL for Windows appears dead
The SITL for Windows discussion appears to be dead since Feb of last year.
I will post my query here in the hope it gets noticed.
"I setup sitl on Windows 7. I followed the recipe in the web documentation exactly. Cygwin is working fine. Mavproxy insta
Read more…naze 32 servo problem
hi..im new in this..im building my tricopter but i dont have any signal for the servo on my naze32 rev5. (i bus mode configured on cleanflight)i have signal only for motor on outlets 1,2,3 but not signal for the servo..im wonder if this FC work for t
Read more…Telemetry Pixhawk and X8R
Hi everyone, I've been investigating on how to have telemetry data on my Taranis X9D with an X8R receiver and Pixhawk, but I still have many doubts.
Can someone please resume me how to do it the easiest way?
Thanks!
Quadcopter not balanced at take off
Hi guys, I am new to Quadcopters and this forum. I just made a Quadcopter F450 with arducopter with GPS. Now today I made its first flight. The problem is that it does not take off. After arming, I give it a little thrust, and only two of its propell
Read more…Electromagnetic Interference
Hi Guys,
I was wondering, why are some industrial inspection drones not effected by EM frequencies? How are they manufactured to not be effected by EM freq?
Thanks!
Read more…Arduplane 3.8 elevon/RC mapping/polarity issue.
Hello all. I have been flying an older apm2.5 board in a delta wing with AP 3.8. I have been running mission planner 1.3.48 for a little while. I recently migrated from elevon mixing on my RC to elevon mixing on the APM. This was a little hard to sor
Read more…mission planner altitude
I'm new to planning missions with the BirdsEyeView-modified AVA mission planner software for programming the FireFly6 VTOL. I want to program mission planner to make the UAV fly 100' LOWER than the launch(hom) point. The program won't accept a minus
Read more…Snapdragon Flight PX4 with Microsoft Airsim
Has anyone here successfully used Qualcomm's Snapdragon Flight with Airsim + UE4?
I've configured AirSim to connect via UDP, and I've verified the SF has a WiFi connection and an IP address, which is pingable from the Windows machine running AirSim. A
Read more…ESC calibration doesn't save in APM
https://www.youtube.com/watch?v=vq0W8olABSY
ESC: Simonk 30A
APM: 2.8
Transmitter: FS-iA10
After ESC calibration, It doesn't save in APM.
How to fix it? help me plz
