Gender
Male
About
About Me:
Computer Engineer
Please tell us a bit about your UAV interest
I've been always interested in all kinds of R/C gadgets. I find really interesting the fusion of R/C and microcontrollers such as arduino.
Activity Feed
Hi!I hav an APM 2.5 with a 90A attopilot sensor. I am wondering if it is really necessary to connect gnd wire coming from attopilot sensor. The thing is I have the power jumper disconnected so I have two power sources on my APM. To avoid ground…
"Hi guys!
Same happens to me!. I have an original 3dr minimosd and a hextronics. Both have had the "OSD gone" problem. I am powering OSD with both 12V and 5V. Strange thing is it used to work before, no problem. But now, don't. I have also strange…"
Same happens to me!. I have an original 3dr minimosd and a hextronics. Both have had the "OSD gone" problem. I am powering OSD with both 12V and 5V. Strange thing is it used to work before, no problem. But now, don't. I have also strange…"
"I have been looking at the diagram again. According to what you guys said, there is a big ground loop. Can someone point mme out where with an arroy or something??
Anyway, maybe I did the diagram wrong but as you said BEC should be connected…"
Anyway, maybe I did the diagram wrong but as you said BEC should be connected…"
"Guys,
I found this http://copter.ardupilot.com/wiki/apm25board_overview/ . Although it is copter related, it seems to explain very well the different type of connection. As for my understanding and as you guys said, it seems that probably I should…"
I found this http://copter.ardupilot.com/wiki/apm25board_overview/ . Although it is copter related, it seems to explain very well the different type of connection. As for my understanding and as you guys said, it seems that probably I should…"
"I will test it today but I am almost 100% sure the grounds are connected, even with the jumper removed.
I am flying a wing like the one on my avatar so, my question is then:
if I want to run all the FPV gear, the APM, MINIMOSD, etc...and The motor…"
I am flying a wing like the one on my avatar so, my question is then:
if I want to run all the FPV gear, the APM, MINIMOSD, etc...and The motor…"
"Sorry when I said removed power supply pin. what I meant was jumper so, with it removed I have independent output and Input power connection. Under the fact that they must be powered independently, do you think there is still a ground loop? Anyway…"
Hi all! Am I correct doing this or should I not connect in parallel the batt for inputs and RX with the bat for outputs and fpv cam.If I don't connect both batteries on parallel, I get only 5 mins of flight .When the battery supplying motor is at…
Hellow guys!!Moved this question here. I have a delta wing with my APM 2.5 . Everything seems to be hooked up properly. Manually I control de surfaces ok. Even if a connect it to Mission Planner I can se the artificial horizon moving accordingly…
Hi!I am setting up my wing with my APM 2.5. Everything is connected just fine. When I try manual mode, all surfaces moves as expected. However, when I turn on stabilize mode, something weird happen. When I do de pitch movement APM compensates as if…
"Hi all! I bought this GPS to use it with my APM 2.5..but the first thing I noticed is that it has a 4 pin connector, instead of the 6 pin connector required for the apm to work. How do you guys connect it to the APM ? I've seen adapters that connect…"
Hi! I have an APM 2.5 and MinimOSD v1.1. The thing is, I have video and the data shown on the video. However, I don't know why the information shown on the video dissapears. If I press reset button, it appears again with correct data. The APM and…
"What happen if I have minimOSD? It says in its wiki not to connect power and USB at the same time. Is this just for APM 2? Mine is2.5 .
For sure i need an external power supply because it does not power up just with the phone connection alone (…"
For sure i need an external power supply because it does not power up just with the phone connection alone (…"
Hi!I have a galaxy s2 with android 4.1.2. I also have the otg cable you suggest. I connect it to APM 2.5 with no battery supply and nothing happens. What is the proper way to connect it? I have different power supplies for apm and inputs and for…
Hi all!I do FPV using minimOSD to display data on screen. My question is if its possible to do both use minimOSD and a 3DR Radio to get telemetry on my laptop. However, I am only able to connect one of these two to my APM 2.5..aren't I??? Is there a…
"I am powering my APM through my 60 AMP ESC. I delayed the response of the servo through the TX firmware and it is not happen anymore. However...I think i should probably use a dedicated Power supply for the APM."
Hi all!I use this digital servo http://www.goodluckbuy.com/md260-260-degrees-metal-digital-servo-fo... to pan my camera. However I noticed that if I move it two fast, it reboots my APM 2.5. I searched and it…
