Gender
Male
About
Location
Kolkata
About Me:
,,,
Please tell us a bit about your UAV interest
Currently I made a aeroquad... M trying to merge it wid the arducopter
Hometown:
Kolkata
Activity Feed
I arducopter code " define " Tab I see/* Expansion PIN's that people can use for various things. */// AN0 - 7 are located at edge of IMU PCB "above" pressure sensor and// Expansion port// AN0 - 5 are also located next to voltage dividers and sliding…
"I connected the faulty board to the FTDI cable again today morning, it was same.. Now it is not even going to force bootloader mode also..
I have mailed this problem to the 3DR team, but they did not reply yet.."
I have mailed this problem to the 3DR team, but they did not reply yet.."
"I tried all the baud rates, still the same..
Moreover I feel there is some other problem .As the GREEN LED is glowing SOLID and the RED LED is blinking at 1 HZ rate..
I dont know if there is a problem with the board will 3DR replace the product or…"
Moreover I feel there is some other problem .As the GREEN LED is glowing SOLID and the RED LED is blinking at 1 HZ rate..
I dont know if there is a problem with the board will 3DR replace the product or…"
I just bought the 3DR 433Mhz radio telemetry kit from DIYDrones.. The two boards of the 433Mhz looks same. After I received the kit I soldered the header pins to the boards and connected to the FTDI cable. Now one board connects fine to the…
I burnt the atmega 2560 on APM 2.. I replaced it with a new Atmega 2560..I am unable to flash the board now with any of the firmwares with APM Planner..Is it that the arduino bootloader is needed on the board to upload firmware..??If so please tell…
"someone please reply... :("
I am going to order this motor from the DIY Drones' storehttps://store.diydrones.com/Motor_AC2830_358_880Kv_p/ac-0004-05.htmNow I saw the datasheet of this motor here http://stuff.storediydrones.com/A2836.pdfwhere the motor is rated as it needs…
I have few APM and OILPANBut one of my first setup is APM with Atmega1280 and the older OILPAN.In this board I cannot find any logs of my flying.. Why is that...??Please help me out.. :(
"I bought the rev 1.1 magnetometer just a month back...And since then I did not fly yet..But I have soldered it to the OilPan and APM and uploaded the AP_COMPASS_TEST code and found that the reading given were fine...So is there still any need to…"
"@ sid
Yes those two pins are short together by default...."
Yes those two pins are short together by default...."
"I bought the rev 1.1 magnetometer just a month back...And since then I did not fly yet..But I have soldered it to the OilPan and APM and uploaded the AP_COMPASS_TEST code and found that the reading given were fine...So is there still any need to…"
"So how do I fix that problem of 0.5Hz flashing rate...??
Or its jus fine...??
I have checked that he GPS locks itself when I take it outdoor....
It takes about a minute for the GPS to get licked..."
Or its jus fine...??
I have checked that he GPS locks itself when I take it outdoor....
It takes about a minute for the GPS to get licked..."
"well I did not face any problem...
I have flashed the GPS...
and yes the blue LED blinks at 1Hx rate...
thats
1sec on
1 sec off
I hope thats ok....??
And it is able to lock itself..."
I have flashed the GPS...
and yes the blue LED blinks at 1Hx rate...
thats
1sec on
1 sec off
I hope thats ok....??
And it is able to lock itself..."
"Where do I download the latest firmware from...??
Cn u please gimme a link to download that...??"
Cn u please gimme a link to download that...??"
"Hehehe..!!
That was jus awesome....
The elevator part was quite funny...when ur friend wid the camera was running upstairs... :P"
That was jus awesome....
The elevator part was quite funny...when ur friend wid the camera was running upstairs... :P"
I have a MT3329 GPS with the DIY Drones new firmware....( AXN1.30_2243_3329_384.1151100.1 )I was to flash it with the old default NMEA firmware....Where can I download the default firmware from....??The main reason why I want to load the default…
