Dale Cruze's Discussions

Tower App Won't Connect on Phone

I am having trouble getting the Tower App Version 3.2.0 to connect to my Android Phone.

3DR sent me this link:

http://ardupilot.org/plane/docs/common-configuring-a-telemetry-radio-using-mission-planner.html#common-configuring-a-telemetry-radio-using-mi

Started by Dale Cruze

Eachine Racer250 and FS TH9x

I am trying to set up the Eachine Racer 250 with a FS Th9X transmitter using a FrSky D4R-II 4 channel receiver. This is the setup that I use for my 3DR Iris+ and I would like to be able to use the same transmitter for both.

Is this combination possi

Started by Dale Cruze

Back Up TH9X Transmitter

I have a Iris+ with the FS TH9X Transmitter.

Does anyone know of a way to backup the settings of the transmitter?

I looked at the Smartieparts.com board, but they tell me I would have to flash and upgrade my firmware and I don't want to loose my origin

Started by Dale Cruze

Iris+ FPV Racer

I have a Iris+ and another one for parts. I am looking for a FPV racer that I can use my FS Th9x Controller and the receiver out of my spare Iris in.

Does anyone have any ideas if there is a racer that will work?

Thanks

Started by Dale Cruze

Controller Low Level Model Alarm

I have a Iris+ with the FS-Th9x Controller.

The controller displays the Altitude and Battery Voltage of the Model. Is there any way to make the controller give a low Batter Level Alarm for the Model?

Started by Dale Cruze

Controller Low Voltage Model Alarm

I have a Iris+ with the FS-Th9x Controller.

The controller displays the Altitude and Battery Voltage of the Model. Is there any way to make the controller give a low Batter Level Alarm for the Model?

Started by Dale Cruze

Tower App Parameters

I am using a Iris+ with the Tower App.

Is there anything that tells what each of the parameters is?

I would like to set a default speed for waypoints instead of setting each waypoint speed individually.

Started by Dale Cruze

Upgrade to Arducopter 3.3.3?

I am using Mission Planner with Arducopter 3.2.1 on a Iris+. I keep looking at upgrading to the latest version. I like some of the new features like BRAKE, but don't want to mess up anything that I have now.

Is 3.3.3 stable?

Is there a list of changes

Started by Dale Cruze

Need TX Switch

I have a Iris+ with the Iris+ FS-TH9X controller.

I found one of my switches was broken today. Does anyone know where I can buy a replacement switch?

If your looking at the controller it is Top Left Rear switch. It is a spring loaded switch and not a t

Started by Dale Cruze

Blade 350 QX2 GPS Issue

I have a Blade 350QX2. I just replaced the main board and compass because it got shorted out. I have installed the new board and was Calibrating everything. I was having trouble getting anything to calibrate. I re-installed firmware 2 and calibration

Started by Dale Cruze

Need Help Charging Battery

I have a LI-24 Lipo/LiFe Charger

http://www.rcplanet.com/DuraTrax_Li_24_2S_4S_LiPo_LiFe_AC_Balancing_Charge_p/dtxp4620.htm

and 3 Zippy 1000 20C Series 2 Cell 7.4 volts batteries which were bought to use on FPV goggles

http://www.hobbyking.com/hobbyking/

Started by Dale Cruze

Blade 350 QX2 Board Problem

We have a Blade 350 qx2 and we had the body off of it. Now when we try and power it up we get a yellow blinking light with a flat sounding tone. The red and blue light blink on the main board and then the blue light goes out and the red light stays o

Started by Dale Cruze

Gimbal Control Iris+

I am using a Iris+ with the Iris+ FrSky controller. When I turn the knob to the right that controls the gimbal it moves up and when I turn it to the left it moves down. This seems backwards to me. Is there a way to reverse this?

Started by Dale Cruze

Help with FPV - New Board

I have a Iris+ with 3DR's First View FPV system. My video transmitter board need replacing. 3DR said they don't sell just the board for their set, but I could use any Transmitter board.

I ordered a Boscam TS351 5.8G Transmitter. When I try and get it

Started by Dale Cruze

Replace FPV Board

I have a Iris+ with 3DR's First View system. I have stopped receiving video and 3DR says I need to replace the Telemetry Board.

If I have to replace the board anyway is there a better system board that would tie in and work with the monitor and antenn

Started by Dale Cruze

No FPV Video

I have a Iris+ with the 3dr FPV kit and a GoPro Hero 3. Usually when you first turn it on the camera and monitor with connect and have a picture. The picture wil randomly cut out. Sometimes I can get it back if I turn the Gopro off and back on. Othe

Started by Dale Cruze

A Slow Stop

I have a Iris+ and I just had to replace my Pixhawk board and I am trying to get all of my settings working again.

I installed the board and updated the quad firmware to 3.3.2. I am also using Mission Planner 1.3.32 and Tower3.2.0.

Now I have a issue w

Started by Dale Cruze

No Gimbal Power

I have a Iris+ with a Tarot 2 Gimbal. I just replace the Pixhawk board, and updated my firmware the latest.

I was flying yesterday and Loiter mode was drifting towards a tree and the Iris took a hard landing.

Now the gimbal won't work. I have Green and

Started by Dale Cruze

Follow Me Mode

I have a Iris+ with Firmware 3.2.1 and Tower 3.2.

I have been trying to get the Follow Me Mode to work. I have read the Follow Me Instructions and it says to take off and Loiter then click on Follow Me in the software. I can't find a Follow Me window.

Started by Dale Cruze

Help, First Flight Woes

I just purchased a used Iris+ with gimbal and GoPro3 and FPV. I have downloaded the Tower software to my Samsung Galaxie S5 phone. I have not been able to get the Iris to connect to my phone with the WIFI. I cannot find the wifi signal from the Iris.

Started by Dale Cruze