I did an update from Windows 7 to Windows 10 and now I am having problems with the HUD Display missing in Mission Planner. Also, I have to go to Task Manager to close Mission Planner too.
Attached is my current Mission Planner display in "Flight Data
Read more…I purchased the Minimosd from 3D Robotics and everything is wired and works between my quad and FPV. My problem is when I go to the Minimosd-Extra to configure the panel layout on my PC. I keep getting the following message. "Failed to Upload New
Read more…While flying my APM 2.6, my quad went into RTL. Based upon my log, the RTL was triggered by the low voltage (10.5). Although, I don't understand why, because I had the failsafe options disabled.
I was flying my F450 in the woods so I didn't want the
Read more…I just updated Mission Planner and now I get a message "Geofence Breach". I currently have the Geofence disabled.
Is this a glitch in the update, or do I need to change a setting?
Thanks.
Read more…I have been trying to get an APM 2.6 in working order. Unfortunately, this time the copter crashed from 12 feet in the air and destroyed three Graupner props and a 8000 mAh lipo. Note: This is not my first UAV build.
I have flashed, erased and
Read more…The following message appeared when I checked for updates. I should add, my logs are not recording.
"Update Faliled. File download does not match Hash: Geo Utility.dll"
What should I do?
This is my second APM and it is getting very frustrating. I did
Read more…Approx. every 10 seconds my quadcopter will slight twitch/Pulse during my test flights. I am using the APM 2.6 flight controller.
Any advise, or direction would be greatly appreciated.
Thanks.
Read more…I have did the Compassmot on my hexacopter last year, but 3DRobotics support said the following for my quadcopter that I have just completed and ready to test.
Hello Dan.
Glad everything is fine now!
A quick note, we have reports that the Compassmot is
I went to Mot_Spin_Armed and set it to 0. When I arm and flipped my assigned safety switch on the TX to"On", all four motors will spin. After raising the throttle, and lowering it back to zero, I may have three out of the four motors continue to sp
Read more…I built an APM 2.5 and had very little problems, but on my APM 2.6 I am not able to get my PC to recognize Arduino Mega 2560. I downloaded the zip file and extracted it. Then I went to "Other Devices" and scanned, but no luck. I do not see the Ard
Read more…I have been using the APM 2.5 and haven't had a problem finding the COM to connect within Mission Planner. I now have an APM 2.6 that I am trying to setup. Although, I am not able see the Arduino Mega 2560. I have the drivers on the hard drive (Wi
Read more…When loading 1.2.85, a message, "Map change failed. Try zooming out first".
It doesn't seem to matter if I zoom in or out within the map. The message always comes back when loading the software.
Read more…Since I did my last Mission Planner update yesterday, I am not able to execute Mission Planner. Has anyone else run into the same problem too? Also, I am using Windows 7.
Read more…I am currently using the Spektrum DX7s and it has worked well for me using the APM 2.5 on my hexacopter. All though, after setting up the transmitter for six modes for Arducopter and the pitch/tilt control on my camera, I am maxed on my channels. N
Read more…What is the min. recommended value to be away from the PWM limits of other modes?
Even though the Flight Modes will switch within the Mission Planner, I have found during a test flight a couple of my mode values were too close to one another. I reali
Read more…Today I was testing the Alt Hold and Loiter modes. When I switched to Loiter for the first time, my hexacopter locked into position. After Loiter, I switched back to Stabilize. Everything seemed okay. Although, when I went back to Loiter, the hex
Read more…After updating to 1.2.64 in the Mission Planner, I am getting a "Compile Failed" message when trying to graph my tlog.
Is this a glitch?
Read more…I would like some help reviewing my tlog. I wanted to test the Alt_Hold and Loiter, but my flight times stink. The hexacopter is seven pounds and I am using a 4S 5000mAh 50c lipo. Per the voltage_battery, It seems I get a considerable drop in voltag
Read more…I did the compassmot calibration and at full throttle I keep getting 38%. I know it is in the low range of the gray area. I should be okay per compassmot, correct? All of my other calibrations look good.
Thanks.
Read more…I just installed Ver. 3.0.1, but when I power my Hexacopter (APM), I am only getting a single beep instead of two beeps before it goes into it's tune. The Mission Planner is not indicating an error, and I am able to arm the copter. Note: All motor
Read more…