Gender
Male
About
Location
Los Angeles, CA
About Me:
Pilot, Modeler, Robotics
Please tell us a bit about your UAV interest
Interested in Autonomous flight, obstacle avoidance, code, DIY, FPV, and innovation!
Hometown:
Los Angeles
Activity Feed
"Because of other projects, I have stepped away from my 3DR Quadcopter with the Pixhawk.
From memory, I think I went back to the drawing board, re-flashed the firmware, and did a complete setup from the beginning in Mission Planner.
Then it all…"
From memory, I think I went back to the drawing board, re-flashed the firmware, and did a complete setup from the beginning in Mission Planner.
Then it all…"
Hi, My pixhawk is showing a pre-arm error of No RC Receiver.It's there.I can calibrate radio, and, throttle down and to the right produce tones.So it's there.I've reinstalled firmware, checked my connections. No joy.Any ideas?
"Thanks for your reply.
I was hoping this was an obvious issue experienced by another user.
Supplying logs will garner more responses to this post?"
I was hoping this was an obvious issue experienced by another user.
Supplying logs will garner more responses to this post?"
"Thanks for all your tips, advice and concern.
Fly safe."
Fly safe."
"Follow up:
Thanks for all your suggestions, very helpful. I ended up discovering that the cell in question was dead. I desoldered it from the pack for a charge attempt and it would not hold.
Thanks Søren, I removed the cell and turned my 5s into a…"
Thanks for all your suggestions, very helpful. I ended up discovering that the cell in question was dead. I desoldered it from the pack for a charge attempt and it would not hold.
Thanks Søren, I removed the cell and turned my 5s into a…"
"Thanks...
So V+ on the balancing wire, and - on any ground?"
So V+ on the balancing wire, and - on any ground?"
"Thanks for the warning... I would never open a lipo cell, just check the connections."
"Yes, It's 0.0 and I tried the NiMh method, and the remaining 4 cells all charge fine.
Just have to figure out how to charge that cell with 10mAh only. And Safely."
Just have to figure out how to charge that cell with 10mAh only. And Safely."
Hey,I'm fully aware of the dangers of opening up a lipo.I know that it might be safer to render it inert in saltwater and throw it away.I understand that sometimes, charging a dead cell at 10mAh, might bring it back to life.Any ideas on the best and…
"Hey Guys,
I fixed my Miniosd issue months ago.
Refer to my diagram above.
I have no idea about the remzibi.
"the dance" is the hours one spends trying to figure this stuff out.
Sorry I couldn't be of more help.
D"
I fixed my Miniosd issue months ago.
Refer to my diagram above.
I have no idea about the remzibi.
"the dance" is the hours one spends trying to figure this stuff out.
Sorry I couldn't be of more help.
D"
Just got a brand new APM 2.6.It won't connect to terminal, initial setup/firmware install, or Mav link in Flight Data in latest MP. (updated today)My com port sees the Mega 2560, but "no connection" anywhere.When I first click connect in terminal,…
Strange... For the past few days now, anything I type into the Forum search field returns a blank!Our apologies - we couldn't find any discussions matching your search.Suggestions:Make sure all words are spelled correctlyTry different or more…
"Thanks but reset does nothing but blank the video for a second. There is no "update char set" message, there's absolutely zero overlay graphics.
I've triple checked my connections, mavlink works, and, I've even updated the minimOSD with the…"
I've triple checked my connections, mavlink works, and, I've even updated the minimOSD with the…"
I've set up my minimOSD as per the diagram below, and, my Transmitter, Camera all work fine, however, there is no overlay data from the APM through the minimOSD board.When I first set up the configuration below, the minimOSD board showed a…
Hey... Relative Newbie help, please.Can't get my Camera Servo to work.I've searched thru the forums and posts already. I'm trying to set up my Camera tilt with the 3DR suppled camera gimble and servo.I've plugged in the servo's signal wire to APM 11…
