About

Gender

Male


Location

Sindh


About Me:

Electronics student


Please tell us a bit about your UAV interest

Final year project


Hometown:

Hyderabad


Activity Feed

Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
Aug 24, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"dear my prop are of 1045 Size (i think it means 10 inch) and motors are of 1000KV and let me tell you that the esc which is powering my APM is little bit more heating up than other three ESC"
Aug 23, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear Forrest

Thankxxx for your suggestion i did not recieve my 3s battrey yet i will tell U when i get my battrey.
and i think you are 100% right that the issue may be of my battrey bcz as i charged my 2s battrey to 8.2 volts than my drone bcomes…"
Aug 23, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear forrestt 
i am really reallly sorry i am still not clear with your past two reply about powering APM bczz i have sent a diagram of my powering way .. and you said i am doing wrong but in your reply the methods you gave me are the same as my…"
Aug 22, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"should i connect the ground wire too ..... i am using hobbyking simonk 30A 5v2A ESC BEC"
Aug 22, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear Forentz.
first of all thank you for your continous support. i ordered a 3s lipo and it is on the way . but yesterday my friend told me that there may be some problem in my wiring of esc to output rail let me tell you how i am wiring my whole…"
Aug 21, 2018
Hamza fayaz replied to Charles Winter's discussion Powering the Ardupilot Board
"Dear 
I need to know that i am not using power module and i want to power my APM 2.8 correctly 
the JP1 is ON and i am connecting all three pins (s,+,-) of my ESC BEC (5v,2A) to output pin 1 and for all other ESC's i am only connecting the signal…"
Aug 20, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear Forrest
i have sent you the video  of my first flight . now i am facing an issue that one of my motor is not moving so fast while other three motors are moving good enough that it is producing thrust to lift the quad... but i cant fly only…"
Aug 19, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear  Forrest Frantz
i thank to you and mr Shivam who helped me alot now my Apm is almost working good but there is only little problem that after arming my APM as i rise my throttle my motors start spining but after 4 to 5 sec all motor suddenly…"
Aug 15, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"yes you are right when i am triming my throttle all the way down  and yaw trimm all the way left than APM is arming easily other wise not arming....
but as you previously said that i should radio callibration while all the trim must be in centere…"
Aug 13, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"see the picture of mt TX and there you can see that there are switches for (AIleron,Elivator,Throttle,Ruddle)
and throttle switch is down which means it is reverse.. i  did this becasuse when throttle swich is on normal in the Radio callibration…"
Aug 12, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"I am using APM 2.8 with three Simonk (30A, 5v, 2A ESC BEC) and one mystery (5v 3A ESC BEC) and let me tell you that i am powering my APM using ESC (with jp1 connected) i am not using Power Module.
after callibration.motor are starting at same…"
Aug 12, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear when i calibrate my radio while all trim stick were in centered and after than i  calibarated my ESC and as i arm my apm. motor starts spinning at the same throttle but after moving throttle up and down two or three times my APM is disarming…"
Aug 11, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"Dear Shivam Gupta 
i followed your instructions and now all motors are start spinning at the same time but as i am giving full throttle motors spinning at full speed  but as i rise and low the throttle APM disarming automatically Shivam Gupta said:…"
Aug 11, 2018
Hamza fayaz replied to Hamza fayaz's discussion APM 2.8 Armed (solid Red LED) but motors spinning slow in ArduCopter User Group
"i have done  but prob still exist"
Aug 11, 2018
Hamza fayaz posted a discussion in ArduCopter User Group
Deari am a beginner i have set up each and every thing but when i armed my quad copter . motor no 1 satrt spining after 50% throttle whereas other 3 motors does not start spin  but when i move my pitch than one of my motor start spinning too but my…
Aug 11, 2018
More…