About

Gender

Male


Please tell us a bit about your UAV interest

hexacopter 820, Pixhawx, 3DR radio clone


Hometown:

Brno


Activity Feed

Ivosch replied to Ivosch's discussion battery pack 2P
"In one pack it will act as 4S2P, I can charge it and balance with one power and one balance connector. Less wires, better handling/connecting. I have charger for 6S battery max, I can't charge two 4S together. Parallel connection when batteries are…"
Jan 11, 2017
Ivosch posted a discussion
Hello,as I got information, Hobbyking won't be selling Multistar 4S batteries 8 and 10Ah anymore. I would like to build pack from 2x 4Ah which are still in stock in EU. I wanna tape both batteries to one piece and solder power and balance connectors…
Jan 11, 2017
Ivosch replied to Ivosch's discussion DIY ESC/engine/propeller tester
"hi, sorry for the delay, I'm working on my 3rd hexacopter, I prepared a brief instructions how to build my tester called "Buzz" :)
here it is: http://diy.ivosch.cz/buzz-drone-engine-tester/"
Nov 24, 2016
Ivosch replied to Don Megabyte's discussion Garbage output mixed in w/ overlay MinimOSD
"Actually in the new firmware is not possible disable OSD by screen switching so I load my previous firmware (MinimOsd_Extra_Copter_R800.hex) and it works now great again..."
Nov 20, 2016
Ivosch replied to Don Megabyte's discussion Garbage output mixed in w/ overlay MinimOSD
"whohooo, finaly, I was able to get it work when I load new firmware and charset from the https://github.com/night-ghost/minimosd-extra."
Nov 20, 2016
Ivosch replied to Don Megabyte's discussion Garbage output mixed in w/ overlay MinimOSD
"Same issue. I tried 5V trick and reload firmware + charset and no change :(
Any other ideas ?"
Nov 20, 2016
Ivosch replied to Alexey Kozin's discussion My version of onboard oled display for arducopter 3.4 in ArduCopter User Group
"will it be part of the firrmware 3.4 REL ?"
Oct 26, 2016
Ivosch posted a discussion
Hello,I have almost everytime small issue during take off in stabilize mode @pixhawk and arducopter 3.3. When hexacopter is on the ground and I'm increasing throttle, drone starts to tilt to one side. According to log file, motors one the one side…
Oct 23, 2016
Ivosch posted a discussion
Hello,I have a pixhawk with internal compass + external GPS M8N with compass. There are to high interferences on internal so I use external compass as primary. But now I would like to have backup compass. There is a option for 3rd compass in Mission…
Oct 10, 2016
Ivosch replied to Ivosch's discussion DIY ESC/engine/propeller tester
"I created a video how works automatic mode: youtube."
Sep 7, 2016
Ivosch replied to Ivosch's discussion DIY ESC/engine/propeller tester
"That is true, every ESC has different throttle calibration and behavior. But to compare ESC's actually I don't need RPM. What is important to me is max thrust and efficiency. To compare efficiency is good chart efficiency vs thrust which I can…"
Sep 7, 2016
Ivosch replied to Ivosch's discussion DIY ESC/engine/propeller tester
"Nice job, it looks similar. How do you measure current ? For me it is hard to get effective value when ESC is switching 3 phases.
I want to measure vibrations to see how propellers are balanced. Because of this the motor has to be mounted on the…"
Sep 6, 2016
Ivosch replied to Ivosch's discussion DIY ESC/engine/propeller tester
"Thanks, but it is not so powerful.
I'm sending data through Arduino USB, so it is easy copy and paste table from Serial monitor to Excel. In the future I would like to implement RPM sensor + maybe microphone to measure noise."
Sep 5, 2016
Ivosch replied to Ivosch's discussion DIY ESC/engine/propeller tester
"more picturesIMAG0818.jpgIMAG0821.jpgIMAG0824.jpg"
Sep 5, 2016
Ivosch posted a discussion
Hi, I made engine tester based on arduino. I would like to ask you, if someone/something does exists ? I found only too expensive commercial project: https://www.rcbenchmark.com/.My cost only few $$ and I dont know if Im missing something. Here is…
Sep 5, 2016