Gender
Male
About
Location
Groningen
About Me:
I am flying mainly with F3J & F3B class gliders.
Please tell us a bit about your UAV interest
stootkop.nl
Hometown:
Groningen
Activity Feed
"Hello Richard,
Thanks!!
This weekend I rewire my copter like you did.
Keep you posted!!'
Regards, Michel"
Thanks!!
This weekend I rewire my copter like you did.
Keep you posted!!'
Regards, Michel"
While testing the Arducopter pos./alt. hold function (ArdupiratesNG) something goes terribly wrong.Initially it was a success but suddenly the copter starts to drift and within a few seconds it was beyond a controllable visual range. The flight…
"@ Doug & Robert,
All the soldering looks ok under the microscope.
There is a possibility that the i2c bus not functioning properly.
Is there anyway to test the i2c?
Regards, Michel "
All the soldering looks ok under the microscope.
There is a possibility that the i2c bus not functioning properly.
Is there anyway to test the i2c?
Regards, Michel "
"Hi Doug and Robert,
Make it three people.
Like you I get also only zeros with the CLI.
Tommorow I will take a closer look under a microscope.
Keep you posted.
Regard, Michel"
Make it three people.
Like you I get also only zeros with the CLI.
Tommorow I will take a closer look under a microscope.
Keep you posted.
Regard, Michel"
"The answer is Ardu V2.4, this version supports the V2 shield."
"Hi,
To avoid unplug GPS while programming I have ordered the V2 shield.
With this new shield it is not possible to get a GPS lock, the blue led flashes constantly.
If I uses my old shield I get a fix within a few seconds.
What could be wrong?…"
To avoid unplug GPS while programming I have ordered the V2 shield.
With this new shield it is not possible to get a GPS lock, the blue led flashes constantly.
If I uses my old shield I get a fix within a few seconds.
What could be wrong?…"
"Hi simon,
I had similar problems with failsave V1.6, now with failsave V1.5 my Ardu operates normaly.
Regards, Michel"
I had similar problems with failsave V1.6, now with failsave V1.5 my Ardu operates normaly.
Regards, Michel"
"I have successfully flash the V1.5 today, I try V1.6 no errors during programming but the AP doesn't respond if I switch it on. No problem I am migrating to the Jeti 2.4 soon, lost of signal recognition is useless with 2.4. Still have the problem no…"
"Update,
Thinks going weirder.
If I turn the Z sensor 180 degrees and recalibrate the problem moves to the aileron (stays fixed) and my elevator stabilizes normaly in fly by wire mode.
I try this several times and each time the problem switches."
Thinks going weirder.
If I turn the Z sensor 180 degrees and recalibrate the problem moves to the aileron (stays fixed) and my elevator stabilizes normaly in fly by wire mode.
I try this several times and each time the problem switches."
"Hi Chris,
Thanks for your reply
No with V1.6 nohing works only manual mode. With original failsave firmware loaded I have the above mentioned problems.
I still use FM but a 2.4 Jeti upgrade is ordered.
Michel"
Thanks for your reply
No with V1.6 nohing works only manual mode. With original failsave firmware loaded I have the above mentioned problems.
I still use FM but a 2.4 Jeti upgrade is ordered.
Michel"
"Hi Chris,
Yes its the same.
Is it possible that the failsave is corrupt?
I try to load V1.6, no errors but I am unable to switch to AP mode only manual stat and no blinking leds.
I followed exactly the tutorial and uses a AVRISP mk2 programmer.
The…"
Yes its the same.
Is it possible that the failsave is corrupt?
I try to load V1.6, no errors but I am unable to switch to AP mode only manual stat and no blinking leds.
I followed exactly the tutorial and uses a AVRISP mk2 programmer.
The…"
"Update.
If I load V2.2.3 everything seems to work normal.
So I download a "fresh" V23 and again no stabilisation on elevator."
If I load V2.2.3 everything seems to work normal.
So I download a "fresh" V23 and again no stabilisation on elevator."
"Hi,
Could anybody explain the following strange behaviour.
While flying in waypoint/RTL mode my plane stabilizes aileron and elevator,
But if I unplug the GPS (fly by wire) the plane stabilizes only on aileron, my elevator gives eprox. 30 percent…"
Could anybody explain the following strange behaviour.
While flying in waypoint/RTL mode my plane stabilizes aileron and elevator,
But if I unplug the GPS (fly by wire) the plane stabilizes only on aileron, my elevator gives eprox. 30 percent…"
"I also fried the 74ACT157, I replaced it with a 74HCT157 (cmos), now my servo's run directly to the corner. What could be wrong? Perhaps the gate stays down or something like that. I try a 10k pullup resistor but no positive result."
"That will do the job for sure.
I found also this.
http://www.firmtronics.com/rc-products/digimix-3.php
Its free programmable."
I found also this.
http://www.firmtronics.com/rc-products/digimix-3.php
Its free programmable."
"Hi Chris,
Thanks for your reply.
No problem, aileron and elevator are sufficient i believe.
Is there any way to copy a servo to output 4? To avoid a Y cable (V-tail or aileron)
Regards, Michel"
Thanks for your reply.
No problem, aileron and elevator are sufficient i believe.
Is there any way to copy a servo to output 4? To avoid a Y cable (V-tail or aileron)
Regards, Michel"
