Location
Bangkok
About
About Me:
-_-
Please tell us a bit about your UAV interest
Fixed wing
Hometown:
Bangkok, Thailand
Activity Feed
"Hello Simon,The last time I played with the ArduPilot (328) was with ArduPilot_2_7 and ArduPilot_2_8 with ArduIMU+ V2 and the result was not better than ArduPilot with Thermopile. At that time, the developers were busy with making APM1 work. So…"
"Thank you, Krzysztof."
"Hello,
I think there is more to the missing bootloader than you might think. I am in the same situation here. But when I finish putting bootloader and upload APM firmware. I notice that the LEDs in the bottom board are different. Usually with…"
I think there is more to the missing bootloader than you might think. I am in the same situation here. But when I finish putting bootloader and upload APM firmware. I notice that the LEDs in the bottom board are different. Usually with…"
"Hello Michael,
Nice feature.
Best wishes,
Peter"
Nice feature.
Best wishes,
Peter"
"Does this newest version come with ability to load/save missions to/from a file? Last I checked the previous version dropped this capability."
"Last I did was 2.4 for 168 and 2.7.1 for 328. Is there any other variants that work for these boards? Please help."
"I have a number of legacy Ardupilot boards, in fact 5x 168 and 3x 328. So I would like to ask for your help to locate the right version for 168 and 328. Last I did the test, none of them worked well in Auto mode. So I think I like to do it…"
Hello,I just got around to use APM2 that I purchased sometime ago. I downloaded arduplane2.33 and use Arduino 1.0 to upload the code. I followed the instruction to add "#define CONFIG_APM_HARDWARE APM_HARDWARE_APM2" to APM_Config.h.. The compile…
"Hello Paul,
MAVLink comes with target altitude. However, now it seems to work fine. So I think it's a matter of APM not working at certain time..
Best regards,
Peter"
MAVLink comes with target altitude. However, now it seems to work fine. So I think it's a matter of APM not working at certain time..
Best regards,
Peter"
"Hello Paul,
I couldn't see the 3D models. How can I increase the Lat/Lon decimals? From the log, do you see that APM is trying to reach target altitude 0.0ft? But when I get home and switch on Auto mode from my desk, target altitude is 656ft…"
I couldn't see the 3D models. How can I increase the Lat/Lon decimals? From the log, do you see that APM is trying to reach target altitude 0.0ft? But when I get home and switch on Auto mode from my desk, target altitude is 656ft…"
"Just to add. I can read waypoints from 1.0.89 Mission Planner and see that I set the waypoints to be 200m above ground as well. So I think it's not the Mission Planner. Please help."
"Mark, I think you should check whether your dip switch settings are correct. This looks like an Elevon setup. Please check DIP switch 4.
Peter"
Peter"
"@u4eake - there is a huge difference between the Netherlands one and the TED one. The one you showed is an insect-like flapping wing. The TED one is very amazing. The bird wing is creating both lift and thrust. The inner wing is generating lift,…"
"Hi Alastair,
Finally I've got it to work. Actually the error I saw was okay. I saw this error after
I tried to program bootloader from Arduino 022:
avrdude: verification error, first mismatch at byte 0x3e000 0x0d != 0xff avrdude:…"
Finally I've got it to work. Actually the error I saw was okay. I saw this error after
I tried to program bootloader from Arduino 022:
avrdude: verification error, first mismatch at byte 0x3e000 0x0d != 0xff avrdude:…"
"Hi,
I just changed the chip for 3 of my boards. But I have the same problem with you. I have Sparkfun AVR Pocket programmer. But it doesn't work. If you already know how to do this, please let me know.
Thanks!
Peter"
I just changed the chip for 3 of my boards. But I have the same problem with you. I have Sparkfun AVR Pocket programmer. But it doesn't work. If you already know how to do this, please let me know.
Thanks!
Peter"
