About

Gender

Male


Location

Rio Grande do Sul


Please tell us a bit about your UAV interest

FPV long range, endurance, anything about RC models...


Hometown:

Porto Alegre


Activity Feed

RdanielK replied to Randy's discussion Copter-3.3 beta testing
"+1 - I also would like to have an option to disable the internal compass. I believe it would be beneficial to the system."
Sep 29, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Hi Eric,Thanks for reporting back your tests... I received another 2 pixhawk boards and I repeated the tests and I got the same results... receiver failsafe not working in ac3.2.1
When I have the firmware 3.1.5 loaded everything works, load the…"
Sep 14, 2015
RdanielK replied to Randy's discussion Copter-3.3 beta testing
"Thanks for your reply...
I tried in 3 different pixhawk board, and in all of them receiver failsafe would work in ac3.1.5 but not in the ac3.2.1, so I understand that it was a firmware problem.
Anyway, is there anyone that could confirm that…"
Sep 14, 2015
RdanielK commented on Randy's blog post ArduCopter 3.2.1 released
"One of the reasons that I upgraded to the copter 3.2.1 was the ability to use two gps units... as I understood it should switch to the gps with better look automatically right? I was doing some tests today and by some reason the gps unit connected…"
Sep 14, 2015
RdanielK replied to Randy's discussion Copter-3.3 beta testing
"As per wiki instructions( http://copter.ardupilot.com/wiki/configuration/throttle-failsafe/ ) there is 3 ways that you can set radio failsafe.

Low-Throttle method
No signal method
Receiver method

I'm referring to the 3 option. It was working on…"
Sep 10, 2015
RdanielK replied to Randy's discussion Copter-3.3 beta testing
"Does anyone knows if the receiver failsafe option will be back on AC 3.3 version?"
Sep 10, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Does anyone knows if we have any developer looking into this issue?"
Sep 10, 2015
RdanielK replied to Ted Weerts's discussion How to reduce the mag field reading
"Hello Ted,

I know that this is an old post but I'm experiencing the same issues than you... With my board outside of the frame my magfield is 570.
Have you figured out what needs to be done to fix this issue?
Thanks!"
Aug 15, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Thanks Hugues! I'm glad that you got to see what I'm trying to demonstrate here...

Hope we could have some of the DEVs looking into it."
Aug 4, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"and as I said in the opening post, the problem is when you set failsafe using the receiver failsafe.
as per wiki instructions( http://copter.ardupilot.com/wiki/configuration/throttle-failsafe/ ) there is 3 ways that you can set radio failsafe.…"
Jul 31, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Hi Hugues,
I just think that if it was working in 3.1.5 and this is an option in the wiki, why it is not working anymore?
And if we get to the conclusion that it is not supported and developers won't fix it, so we have to remove this option from…"
Jul 31, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"And is not just about RTL, on 3.1.5 I could have my camera pointing to a specific direction in case of failsafe, now this function doesn't work anymore, FC will hold last position before loose signal."
Jul 31, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Hi MarkM,
Receiver is set to pre-determined position in case of lost of signal... just look at logs and you will see itIf receiver failsafe is not supported anymore, it should be removed from wiki, it would avoid people getting in trouble.I still…"
Jul 31, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Hi Hugues,
Independent of the best way to setup the failsafe, can you see that there is a problem that didn't happen in firmware version 3.1.5?"
Jul 31, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"receiver changes PWM value but copter keeps spinning(yawing).
Are you saying that the receiver is in fact changing the yaw pwm when you turn off the transmitter and the pixhawk is ignoring the change?

That is exactly what is happening, just look at…"
Jul 30, 2015
RdanielK replied to RdanielK's discussion WARNING: Receiver failsafe not working in Copter 3.2.1
"Hi Eric,
When connect to mission planner via USB if I turn off your radio in the flight mode screen I will see the flight mode changing to RTL as well, but if you have a look at the flight data screen in your HUD you will see that once you turn off…"
Jul 30, 2015
More…