Gender
Male
About
Location
London
Please tell us a bit about your UAV interest
DIY copter builds, FPV for fun, aerial video and photography, high res imaging
Hometown:
London
Activity Feed
"79 USD... really?"
"Patrick, thanks a lot for this! awesome work!"
"if it sounds to good to be true, it normally is ;-) stable video without a gimbal can't work!"
"nice tip Marco. I'll try it out. My trick so far was: little stick forwards and a bit of rudder. After some yawing the copter will end up flying sideways and then you know where the nose is."
"+1 for using the new servers!"
"http://www.simtoo.com/page.php?id=132#page3 "World First Foldable Drone"
bit of a bold claim..."
bit of a bold claim..."
"awesome! thanks for sharing. The specs are really good! Sony exmor (backside illuminated chip!!) And they kept the price. The only bad thing about the pi cameras is the lens. I haven't tried yet, but it should be possible to remove it and mount a…"
"4. can be T-ed off from a TX line from 1. or 2. I even triple split and hook up lines to an OSD and Frsky telemetry via teesny from one telemetry port."
"Hi again, is it possible to configure RSSI? I tried with 3.4dev setting RSSI_ANA_PIN to 103 and RSSI_PIN_HIGH to 3.5. But no RSSI is reported in MP's HUD: "rssi: 0". I'm using an FrSky X8R receiver. RSSI is working ok with above configuration on a…"
"I've got 1.3.37 build 1.1.5932.22903 like yours. I normally click on Help/Check for BETA Updates every other day.
Just to make sure it is not Pixracer's fault I just tried to upload APM via MP to an AUAV-X2 board. Not working either. So maybe a MP…"
Just to make sure it is not Pixracer's fault I just tried to upload APM via MP to an AUAV-X2 board. Not working either. So maybe a MP…"
"Hi all, I finally got my pixracer. I managed to flash PX4 firmware using QGroundControl. But I cannot flash APM using Misison planner or APM planner. It detects the board, downloads the file, but then after a while a message 'error uploading…"
"I like it. I hope ardupilot.org will be more focussed on technology development and DIY again. In the last year "DIY"drones has become more or less just an advertising board."
"Is this the first copter you are building? If so I would say that a 1m diameter 16inch prop beast is a bit ambitious for a first build. Why not try a small 250 or 300mm 'mini' quad or hex as first project to learn how these things work."
"Great idea. I guess overall the air in London will be more bad than good news. But nice to have data to prove this! On your map I just get "MODERATE POLLUTION" or "HIGH POLLUTION" with smiley faces. What measurements are taken and is there any way…"
"just had a look here: https://github.com/diydrones/ardupilot/milestones
The AC 3.4.0 milestone is only 27% complete. I guess now that a lot of developers have had their support withdrawn by 3DR the dev speed might be slowed down a lot. I'm not sure…"
The AC 3.4.0 milestone is only 27% complete. I guess now that a lot of developers have had their support withdrawn by 3DR the dev speed might be slowed down a lot. I'm not sure…"
"I've fitted a pixhawk into an emax nighthawk 250 frame: http://makeitbuildit.co.uk/index.php?route=product/product&path...
the middle section of this frame is a bit wider than the zmr250 style frames."
the middle section of this frame is a bit wider than the zmr250 style frames."
