Gender
Male
About
Location
Odessa
About Me:
technical operations engineer
Please tell us a bit about your UAV interest
UAV, planes, AMI
Hometown:
Odessa
Activity Feed
"can you give me an advice how to implement it?"
"hey, I use JR x-bus receiver in mode B.
It works well with ArduPlane but not with PX4 firmware."
It works well with ArduPlane but not with PX4 firmware."
"Hi!It's excellent explanation how to config Japan Radio. Tested with my XG8 and XG14.So now I have all flight modes (reversed 3-pos stick exactly as you described and changed limits to +75, -75).
Hurray!"
Hurray!"
"ok. Tomorrow will try it on my JR XG14."
"Hi.
What's your progress?I'm going to use my JR XG14 radio with APM but APM has no xBUS support (technically there's no opensource implementations of xBus =( "
What's your progress?I'm going to use my JR XG14 radio with APM but APM has no xBUS support (technically there's no opensource implementations of xBus =( "
"I had the same problem:
"upload succeeded but verify failed: exp 8c got DC at 102254".
As for me, the problem happened because I use Windows VM on MAC (VMware fusion hypervisor). It's very common issue when you use Serial port on a VM.
Try to use…"
"upload succeeded but verify failed: exp 8c got DC at 102254".
As for me, the problem happened because I use Windows VM on MAC (VMware fusion hypervisor). It's very common issue when you use Serial port on a VM.
Try to use…"
"I had the same problem:
"upload succeeded but verify failed: exp 8c got DC at 102254".
As for me, the problem happened because I use Windows VM on MAC (VMware fusion hypervisor). It's very common issue when you use Serial port on a VM.
Try to use…"
"upload succeeded but verify failed: exp 8c got DC at 102254".
As for me, the problem happened because I use Windows VM on MAC (VMware fusion hypervisor). It's very common issue when you use Serial port on a VM.
Try to use…"
"Hey, I started test APM 2.6 with smallest GPS module with built-in antenna - CAM-8N."
"Seems like nobody want help us."
"What on your opinion will be better
- to use APM2.6 hardware (ATmega2560+MPU6000) and APM2.6 software with implemented datalogging and then write additional HAL-library for working with microSD card and bluetooth module?
- or use FlyMaple hardware…"
- to use APM2.6 hardware (ATmega2560+MPU6000) and APM2.6 software with implemented datalogging and then write additional HAL-library for working with microSD card and bluetooth module?
- or use FlyMaple hardware…"
"APM2.6 is opensource project. so you can find Eagle scheme and PCB layout.
That's very easy to export tha list of components from Eagle to CSV doc."
That's very easy to export tha list of components from Eagle to CSV doc."
"oh. there's a problem with FlyMaple. working with Atmel AT45DB321D 32MB flash is not implemented on FlyMaple. Also there's no datalogging implementation on FlyMaple at all."
"We decided to start from FlyMaple with STM32F1 CPU."
"I looked through the list of platforms supported by APM and found that there's a board based on STM32F103RET6 that can run on 8MHz and need only 8mA.
1. Is it possible to remove all unnecessary functionality (Servo and Motor management, receiver…"
1. Is it possible to remove all unnecessary functionality (Servo and Motor management, receiver…"
Hi!I want to build small data logger for our plans. We want to use it on light gliders so every additional gram and mm has great importance. It should be really small, like 50*40*5 mm or less ( I talk about the size of the full device with GPS) and…
"Hi.
I see the same problem.
When I connect my Xbee Pro S2b (version XBP24BZ7) to X-CTU select port and press test
it shows device version "smth unreadable" and when I try to read from Xbee it try to updte firmware, downloads new firmware from…"
I see the same problem.
When I connect my Xbee Pro S2b (version XBP24BZ7) to X-CTU select port and press test
it shows device version "smth unreadable" and when I try to read from Xbee it try to updte firmware, downloads new firmware from…"
