Gender
Male
About
Please tell us a bit about your UAV interest
quadros, planes, gimbals etc.
Hometown:
Zurich
Activity Feed
"Great thank you!!!
Do you know how they were made?"
Do you know how they were made?"
"I have a similar issue
I constantly get a "content type" error at the end of the upload... Tried different log, rlog, tlog, chrome, firefox and it doesn`t work.... Any ideas?
Regards
Andreas"
I constantly get a "content type" error at the end of the upload... Tried different log, rlog, tlog, chrome, firefox and it doesn`t work.... Any ideas?
Regards
Andreas"
"Hi Chris
Intresting!
How do you know it`s APM software? Why would they have cut down the functionalety then? It makes it less usefull but is a lot more trouble for them. Why not just sell the APM hardware in a alu case?
Regards
Andreas"
Intresting!
How do you know it`s APM software? Why would they have cut down the functionalety then? It makes it less usefull but is a lot more trouble for them. Why not just sell the APM hardware in a alu case?
Regards
Andreas"
"After another look at the parameters I discovered that the pitch min/max tuning parameters were both set at 30/30 instead of 30/-30 which would explain why the auto modes didn`t work but not why the plane was not managable in manual mode ..."
"Could you provide the logfiles please?"
"Hi Thomas
Thanks for your quick reply!
It`s an APM 2.6 board powered by a 5v 1a BEC for the APM and the 5a BEC of the YBE 70a ESC for the servo side. Servos are Hitec mg65 I think.
Besides, if the controller rebooted because of a voltage problem,…"
Thanks for your quick reply!
It`s an APM 2.6 board powered by a 5v 1a BEC for the APM and the 5a BEC of the YBE 70a ESC for the servo side. Servos are Hitec mg65 I think.
Besides, if the controller rebooted because of a voltage problem,…"
HiToday I had a crash with my x8 which worked fine for at least 20+ flights. After the automatic bungee launch the plane climbed (step but as desired), I then decidedto switch back to fbwa. Then the plane started spining rapidly, and I couldn`t…
"frame: DIY foldable Tricopter (Based on David Windstral's)
controller/autopilot: Dropix (Drotek)esc: 20a (Tunigly Plush, stock firmware)motors: MT3506 600kv (Tiger Motors)propellers: 12x4.7 (Hobbyking Carbon, much better for this size than the 14x5…"
controller/autopilot: Dropix (Drotek)esc: 20a (Tunigly Plush, stock firmware)motors: MT3506 600kv (Tiger Motors)propellers: 12x4.7 (Hobbyking Carbon, much better for this size than the 14x5…"
"Well, they published some schematics on their page, but no eagle files / CAD drawings...
So design files yes, PCB files NO.
Maybe somone from 3Dr pushes them again?"
So design files yes, PCB files NO.
Maybe somone from 3Dr pushes them again?"
"@benbojangles
What kind of video link are you using there? HD?
If so it looks intressting for the claimed pricepoint!"
What kind of video link are you using there? HD?
If so it looks intressting for the claimed pricepoint!"
"why is this thing so expensive? I mean there is no gimbal, the payload of 500gr isn`t that great and a canon 260 isn`t top notch either..."
"hi randy
thanks for your answer! cable was broken but not completely ripped apart, discovered by testing trough the leads... :-)"
thanks for your answer! cable was broken but not completely ripped apart, discovered by testing trough the leads... :-)"
"btw frantz
I would like to run the Hover analysis myself, but I always get run time error 76. And your log analyzer file works just fine, so I assume the inserted path is correct.
it"s on win8.1/office 2010"
I would like to run the Hover analysis myself, but I always get run time error 76. And your log analyzer file works just fine, so I assume the inserted path is correct.
it"s on win8.1/office 2010"
"Hi Frantz
Sure here you go. But please note that I have the Dropix, and since it comes without case it is sandwiched between ground and top plate with mm EPP in between. This is more to ensure rigidness than dampening since the fc can not move at…"
Sure here you go. But please note that I have the Dropix, and since it comes without case it is sandwiched between ground and top plate with mm EPP in between. This is more to ensure rigidness than dampening since the fc can not move at…"
"Hi
I couldnt dind any information on my problem so far, so Ill ask here in the post.
Unfortunatly, my compass2 offsets remain at 0/0/0 and the external compass parameter at 0...
Is there a way to test if the ext. compass is even working?
Thanks a…"
I couldnt dind any information on my problem so far, so Ill ask here in the post.
Unfortunatly, my compass2 offsets remain at 0/0/0 and the external compass parameter at 0...
Is there a way to test if the ext. compass is even working?
Thanks a…"
