About

Gender

Male


Please tell us a bit about your UAV interest

Hobbies, mapping


Hometown:

Bandung


Activity Feed

opiq commented on Andrew Tridgell's blog post APM:Plane 3.5.0 released
"Hi..
Did I missed something? VTOL support in full parameters list from ArduPlane 3.5.2 corrupt? I am using Pixhawk.


Thanks
Opiq"
Apr 12, 2016
opiq posted a discussion
Hi,When I connect MP to Pixhawk using telemetry, why it was not loaded completely. In unit...description col. I am using Win 8.It also happend in another Laptop. I have update MP to latest version, but didn't work.ThxopiqParam_MP.jpg
Jan 24, 2016
opiq replied to Dave Williams's discussion Using AUX pins as relays for CHDK
"It was very difficult to find S2 multiport in local electronic store, so I decided to bring RX100II to camera service center to wiring shutter and ground out from camera shutter button.And it was work to trigger camera in Pixhawk without any…"
Aug 5, 2015
opiq replied to Dave Williams's discussion Using AUX pins as relays for CHDK
"Hi..
Is this woks for RX100m2 ?

Thanks"
Aug 3, 2015
opiq posted a discussion
Hi...I just upgrade pixhawk firmware from arduplane 3.2.3 to 3.3.0. In 3.2.3 servo gimbal (2-axis) works well, but in 3.3.0 gimbal didn't move at all when pixhawk rolled or pitch up/down.Then I am back to 3.2.3, and gimbal works again. When flying…
Jun 17, 2015
opiq replied to opiq's discussion Navigation line in MP
"Thanks,
This is flight track in auto mode. How I could check if there any oscillation in roll from log file?"
Apr 4, 2015
opiq posted a discussion
Hi..Could anyone explain about curve line below?I Use Mission Planner 1.3.6 and ArduPlane 3.2.2 on Pixhawk. It make the flight track zig-zag in auto mission.ThanksNav_line_MP.JPG
Apr 4, 2015
opiq replied to Dave Williams's discussion Using AUX pins as relays for CHDK
"Previously I am following this method for APM :
http://droneyard.com/2013/10/01/ardupilot-camera-tie-in-tutorial/

I try for Pixhawk and it's work after trial and error with cable connection..."
Feb 26, 2015
opiq replied to Dave Williams's discussion Using AUX pins as relays for CHDK
"Maybe I have solved it....in accidentally way :)
No need any circuit... just connecting red cable from USB to (+) pin and black cable to Signal pin in AUX port. I have tested it and  can trigger camera based on distance...."
Feb 26, 2015
opiq replied to Dave Williams's discussion Using AUX pins as relays for CHDK
"Hi..
I have built Marco's circuit, but it didn't work to trigger the Camera with Pixhawk
I measure Signal pin voltage after plugged in the circuit was 0.0 volts, then I push Trigger Camera Now from MP the voltage jump only to 2,.. volt. If the…"
Feb 26, 2015
opiq posted a discussion
Dear All..I am in big problem right now, I have broke 3 airframe because of it. The problem is when I switch my FX79 to Auto, it goes to waypoint but the altitude goes drop from 200m and throttle seems in full power when maneuver and cannot be…
Feb 19, 2015
opiq replied to opiq's discussion Non-Canon Camera Trigger Based on Distance
"Hi Hugues, I have Canon SX260HS, and considering to buy new Sony RX100 III..

Thanks"
Jan 12, 2015
opiq posted a discussion
Dear All,I am developing UAV for Mapping. I use Canon Camera (SX260HS)+CHDK to trigger the camera based on time interval (intervalometer script) and based on distance (E38 script), both was working well.Now, I want to use another brand of camera…
Jan 11, 2015
opiq commented on keeyen pang's blog post 100KM Challenge
"Hi...log link has broken. Could you send me the log file please...

Thx"
Dec 1, 2014
opiq replied to opiq's discussion X8 Carbon with total weight 4kg in X8
"Jeff, how much weight your X8 ?"
Nov 6, 2014
opiq replied to opiq's discussion X8 Carbon with total weight 4kg in X8
"Iskess,
The propeller is in correct position as your said. Tested before flying, X8 has forward thrust .

The battery, I mean 6S 5000 mAh 25C."
Nov 6, 2014
More…