Gender
Male
About
Location
Muenchen
About Me:
pilote
Please tell us a bit about your UAV interest
multiwii and arducopter
Activity Feed
"Thats is cool, but where can I get the software file for flashing an esc?
Up to now I only flash and find software for multicopter and so on..."
Up to now I only flash and find software for multicopter and so on..."
"Hello,
i found the soltion by using the direct Inputs of ATMEGA 1280 on red Board.
IN1...IN8 are only Inputs of 74LS154 Digital Multiplexer."
i found the soltion by using the direct Inputs of ATMEGA 1280 on red Board.
IN1...IN8 are only Inputs of 74LS154 Digital Multiplexer."
Hello,i want connect at least 4 Potis at Ardupilot Breadboard (i have only the red Board) and send its values via USB to PC.USB-Transmit works in steps of 1,5 sec but i think there has to be a special command to define IN1 ... IN8 as ADC-Input.Can…
"Switch of Firewall and Virus System I have the same problem with Putty"
Hallo,I use 1.1.73 and AC 2.5.4If I check Tune CH6_Loiter_P the Loiter P don´t change, it Changes the Loiter speed.In what unit is Loiter speed? m/s?And is Loiter P with 2.0 default normal before it was 0.5... or so and now Loiter P is 2.0 and…
"Oh I should also test this, looks realy good"
"My Copter:
Motor to Motor 560mm(edge to edge 720mm, that the motors are do not destryed on a crash)
Flightmode Plus
Frame self bild with 15x15mm square alu tube
Autopilot: APM1
motors: 1000rpm/v KDA22-20L (Hobbyking)
esc: TURNIGY Plush 30amp…"
Motor to Motor 560mm(edge to edge 720mm, that the motors are do not destryed on a crash)
Flightmode Plus
Frame self bild with 15x15mm square alu tube
Autopilot: APM1
motors: 1000rpm/v KDA22-20L (Hobbyking)
esc: TURNIGY Plush 30amp…"
"Hallo Since ardcucopter 2.5.3 it do not work anymore for me nothing changed?
Do it work for you on 2.5.3??"
Do it work for you on 2.5.3??"
"Hi, Today I have also testet this version:
http://vimeo.com/39722976
The whole video is in Loiter
2012-04-03 19-51 5.log"
http://vimeo.com/39722976
The whole video is in Loiter
2012-04-03 19-51 5.log"
"I have reupload this :ArduCopter 2.2b4 and it works again.
than I upload over MP the 2.5.3 and it also works, but it´s around 37 deg away
Then I test my old variant via arduino upload, but get an error:
#define MAG_ORIENTATION …"
than I upload over MP the 2.5.3 and it also works, but it´s around 37 deg away
Then I test my old variant via arduino upload, but get an error:
#define MAG_ORIENTATION …"
Hi I have a sparkfun Mag:HMC5843in this version it works perfekt:ArduCopter 2.2b4in the newest version it don´t work 2.5.3is this no longer supportet?thxdruckgott
"Reupload the file to the arduino satelit file and also the arducopter software."
"Do you have checked to bind it?
druckgott"
druckgott"
"Do you have checkted that you have selectet the right board?
I used arduino v22 maybe it´s a problem with the new version.
Normaly this should work perfekt."
I used arduino v22 maybe it´s a problem with the new version.
Normaly this should work perfekt."
"I can not exacty remember you have first upload the binding file to the chip and bind the sattelit and then the file which I have uploaded, but i´m not shure
You have to read the blog exactly and then it works."
You have to read the blog exactly and then it works."
