HowTO – setup GPS on Pixhawk (FW3.3.3)
06/16/16
Problem- Mission Planner Flight Data screen “GPS: no fix”
Solution – In Mission Planner > Initial Setup > Manadatory Hardware > Compass > General Compass Settings > uncheck “Obtain compass declination auto
Read more…Hey everybody,
I got a SF11/C laser altimeter attached to my pixhawk and i want to see the live data from the miniosd to a fpv screen with out using a PC?
is it possible? what do i need?
thanks for helping
Read more…Hi Guys.
I am just wondering if you guys could help me to choose the best propeller to this brushless motor EMAX MT2213 935KV.
-Total Quadricoptero weight 1.5kg
-Brushless motor EMAX MT2213 935KV
-Emax Blheli Firmware 20A Brushless ESC
-LOUREON 4S 14.8V
Read more…I've gone through every USB port on my computer, and about 10 different micro USB cables. My computer wont even recognize the board, (no audible que when plugged in) and mission planner doesnt even define it as a viable com-port when plugged in. I ge
Read more…HowTO – setup GPS on Pixhawk (FW3.3.3)
06/16/16
Problem- Mission Planner Flight Data screen “GPS: no fix”
Solution – In Mission Planner > Initial Setup > Manadatory Hardware > Compass > General Compass Settings > uncheck “Obtain compass declination auto
Read more…DIY drone community,
What are the best practices and protocols for full autonomous, GPS waypoint control flight?
I'm moving away from manual and stabilized flight with my 450 kit build. My flight controller is a Pixhawk running a PX4 flight stack, usin
Read more…Hello guys,
in the simulation there are the following parameters for testing the effects of wind:
SIM_WIND_DIR
SIM_WIND_SPD
SIM_WIND_TURB
SIM_WIND_DELAY
The first and second parameter (direction and speed) are clear, but was does SIM_WIND_DELAY do and wh
Read more…I had EKF disabled until recently.After I enabled it by setting AHRS_EKF_USE = 1 , I see no change.
The EKF and Vibration status displays which are available on clicking on the HUD are not getting updated. The levels are all like this-
I have tried t
Read more…Hi all, this is my last project in co-operation with Virtual Robotix which provided me a new autopilot board to test.
The plane is a Skyray from HK, and i can say the frame is very well dimensioned (loads of room inside the fuselage) and strong enough
Read more…Hello friends. I want to get started in this wonderful world of developing UAVs and would like to advise me where I start , I want to start from scratch and implement complex control algorithms for the design of it . Thank you!!
Read more…Hi had this working the other day it done a calabrate on its own worked fine. now it just moves a bit yellow light comes on then a solid blue light which should flash.went on to mission planner made sure it was all ok fot gimbal to work but blue ligh
Read more…Hi Guys, Recently had a nasty crash with my arduplane setup. It was Flying beautifully, however shortly after the last takeoff in Manual mode I suddenly got a no RC warning on mission planner, lost all input, and the plane throttled UP and dove strai
Read more…Hi,
So missionplanner had a feature that allows the user to send differential gps data to copter gps using the telemetry link. It is called GPS Inject.
Is there a similar feature for qgroundcontrol ?
Thanks
Read more…Hello,
I bought a $22 Neo-m8n, with compass from Banggood.com, and for the money it is working real good. The latest firmware can not be flashed to it, and that's when I realized it was a fake.
Where can I buy one, that is guaranteed to be the real th
Read more…I wanted to do long range telemetry so I got myself a dipole antenna for the modem.
I never could check the range because the plane couldn't get a gps lock anymore, with the modem powered on. With the modem powered off, I had a 3D GPS lock, 17 sats i
Read more…I am using an APM 2.6 that is connected to an Odroid USB via the Telemetry port (UART to USB). I am trying to get MAVLINK messages without the need to keep sending a HEARTBEAT message.
If I switch to USB connection (not telemetry) I get MAVLINK mess
FOR SALE - Asctec Falcon 8 Trinity Commercial UAV
For sale is the latest in Commercial UAV technology in the Asctec Falcon 8 Trinity by Ascending Technologies. This UAV is the most advanced and widely used commercial drone in the world.
Built by one of
Hi all this project is starting from a drawing of parts. We are building a nano quad with revolution cc3d mini.Here is the first design.Made with a old charger box as project enclosure
Read more…Hi all this project is starting from a drawing of parts. We are building a nano quad with revolution cc3d mini.Here is the first design.Made with a old charger box as project enclosure
Read more…Dear All
Soory if this question has been answered somewhere else, my search could not find anything, may be I did not use the right keywords. I'm looking for the easiest way to set up autolanding while being about to define/set approach sector. Presen
Read more…