Something that just came to mind and I haven't even thought about yet.
Does mission planner/apm read your (vehicles) altitude from the first time the gps gets a fix, from the sea level (I doubt) or from the ground level.
So let's say you take off from
Read more…Hello, I have a problem with the Runner 250, I am sending the link video of the runner 250 and DEVO 10:
https://drive.google.com/file/d/0B9ZOUH033H-6dXRiaGhMRHhfeDQ/view?usp=sharing
When I unblock the motors, the throttle stick don´t work, and I can´
Read more…PX4Flow is expensive, I consider implement optical flow algorithm with OpenCV optical flow api and my webcam, does it possible?
Read more…Hi,
Just after some type of lights to put on an multirotor that have an decent brightness and throw distance.
The main purpose of this will be to flood the area in front of the camera with light so that it is possible to film with an normal camera in p
Read more…Hi All,Wondering if I'm just missing the documentation - can you import a DEM into Mission planner or Q Ground Control to have a Pixhawk controlled multirotor follow the terrain?I found this documentation that indicates its possible for fixed wingsht
Read more…I have Mission Planner 1.3.37 build 1.1.5917.13431 for Windows running on Windows 10
The dos "MP boot" terminal says I'm running ArduCopter v3.2.1:
Read more…INFO MissionPlanner.MAVLinkInterface - 6/14/2016 11:26:52 AM 1 ArduCopter V3.2.1 (36b405fb)
INFO MissionP
Hi All,
I'm having trouble getting yaw dialed in. With small stick inputs the aircraft is flyable, but with large yaw inputs it wants to pitch and roll violently, and climb too. I assume that I'm making a noob mistake. I come from Pixhawk and autotune
Read more…Hi all,
I have been struggling setting up Pixhawk for a small sized quadcopter with high kv/response motor/esc equipment as below and would like to share my experience with you guys.
Motor: FR1806-2300KV from RCTimer
ESC: K18A ESC(KISS ESC18A) 2-4S als
Read more…Hello. I'm trying to reduce vibrations for aerial filming. I've already tried everything i can imagine.
I have Tarot 650 sport with 14" props, x4108s sunnysky 600kv motors and 4s battery.
One of my last ideas was: frame is not stiff enough. So my frame
Read more…Hi All,
So I've killed both of my 3DR branded telemetry radios after moving them to a new aircraft. They worked great for a couple of years in a DJI F450. I recently moved one to a new build, along with the DJI E300 power system. The flight controller
Read more…Hello everyone,
I want to mention about my solution for using 6s lipo with arducopter. I soldered ubec on lipo output normally and then for the output of the ubec I soldered xt-60 socket. now when I plugged xt-90-s between esc and lipo arducopter is s
Read more…Hi all,
I'm looking for a motor/prop combination that will give me good endurance (over 45 minutes flying times) on my model. It seems like something along the lines of a relatively low KV motor (maybe this 400 KV one: http://www.rctigermotor.com/html
I have a plane setup with two elevators and I am trying to trim them. I change the trim on one channel and it changes the trim no problem, I change the trim on the other channel and it changes the trim on the same elevator. I cannot trim one of the e
Read more…Hi.
what? Raspberry image to recommend me to use a similar plate to this https://github.com/erlerobot/PXF2.
Thanks
Read more…"EKF_ALT_NOISE: Default is “1.0”. Lower number reduces reliance on accelerometers, increases reliance on barometer."
Now what if I use a laser rangefinder for altitude control in Alt Hold?
Does lowering EK
Read more…Hello everyone:
Today I flew again my quadcopter after 6 months of getting new parts from another crash (also due to an undetermined cause) in January.
The drone I flew today had new battery, new and better motors, better propellers, higher end ESCs,
Read more…Hi,
This is my first post on a forum so I'm sorry, in advance, if I make a mistake.
I'm flying a 3DR quadcopter frame with a apm 2.5. When I first got it, it was used and I powered the board from the usb and the power rail and blew the 3.3v regulator
Read more…hi
i am planning to make a hexcopter and for that i would be needing the respected community help
I have shortlisted the following stuff
1. MOTORS
HobbyKing Donkey ST4010-820kv Brushless Motor
Specs:
RPM/v: 820kv
Dimensions: 51 x 23mm
Shaft: 6.0mm
Voltage: 1
Please can anyone tell me which paramater changes the low voltage cut off setting on the rc timer blheli version esc.
picture is attached.
I'm Planning to do mapping with my quad running on Arducopter 3.2.1 . I want APM to log the Cam messages that get triggered with respect to the distance travelled. I tried editing the bits of the Log_Bitmask. But noway i was able to log the CAM messa
Read more…