Hi,
I've been trying to find the description of all the status messages that can be displayed in the Quick tab of mission planner but have not managed to find it anywhere, could someone point me where to find that?
Thanks!
Read more…UAV drone as a new information acquisition carrier has been widely concerned. With the gradual maturity of technology, because of UAV drone has advantage of good adaptability and easy operation etc, it has been used by more and more fields. And becom
Read more…I’ve set up a conventional fixed wing plane with Ardupilot on a miniPix. I have assigned only three modes, Manual, FBWA and Loiter. Testing on the ground Manual and FBWA work as expected but when I switch to Loiter the motor stops and the servos go h
Read more…Memorial Day sale, ends 2nd June;
1> Memorial Day Sale On Select Lipo Batteries- $10 off Over $110 (Code: HERO10)
2> Memorial Day Sale On Select Lipo Batteries- $20 off Over $198 (Code: HERO20)
3> Memorial Day Sale On Select Lipo Batteries- $35 off Ove
Hi folks, I am trying to connect a Raspberry Pi 3 to the Pixhawk module in a 3DR Solo drone for the purpose of implementing an autonomous school robotics project. The purpose of the Raspberry is for computer vision and to send command messages via Ma
Read more…Hi all
I using a Pixracer 15
I try to use a MinLiDAR and a get “Bad LIDAR Health” I found that if I set the RNGFND_LANDING =1 the warning gone but I can’t found the parameter RNGFND_LANDING.
I use framework 3.6.7
or have other idea?
Read more…I know there are infinitely more intelligent people out here who can possibly help me. I am building a Tarot T18 octacopter. I figure a nice clean wiring solution would be nice so I purchased the Tarot TL8X018 PDB which seemed logical that it would f
Read more…Hello guys!
I'm a new beginner in uav field. My project is to build a Drone for inpection in aviation. I would like to know how to choose a good battery for my drone. I've seen many videos in which people explain how to choose it but i'm not sure to u
Read more…I want to set up a Turnigy 9x or FlySky TH9x or Devention Devo 7 to operate an octocopter using Pixhawk 2.8.4 flight controller. I am a complete novice on transmitter setups can anyone help or point me to a wiki
Read more…Hi there,
I work for a television production company and I am currently doing some research into the exciting world of drones and the evolution of personal flying vehicles.
I am trying find stories of people who have built their own incredible and unu
Hi all,
I went to test my drone with pixhawk 4 in position mode and it acted strangely. It works perfectly fine in manual mode but when i switch to position mode, the drone starts twitching in all directions and oscillates, eventually spins out of con
Read more…I am currently building a 1.2 meter electric pusher flying wing which I would like to setup for auto flight and am looking for advice on what to use as a flight controller.
My radio is Frsky X9D and whatever receiver is required. Probably a X8R.
I am s
Have been troubleshooting an ESC calibration problem. Have run many experiments and have an issue of ESC's not calibrating due to not seeing full throttle PWM. Works fine with APM 2.8 controller.
Confused about servo page on MP. When I go to full t
Read more…I am trying to make my own quadcopter that has a Pixhawk Mini 4 as a FC, and using a Spektrum DX6e as a controller, and using Mission Planner ArduPilot.
We are having some trouble with something, but I don't know what the root cause is. When we connec
If you are looking dji drones or action camera from UAE, I will prefer to take from alGadgets Electronics. They are giving best price and fastest same day delivery.https://www.algadgets.com/
Read more…Hello all,
I'm new to this site, but uninterested in any thoughts, kits or suggestions on what i should be planning to take a DJI Phantom 3 standard body to the next level ? Note all of the electronics got wet. So this will be a build from the body on
Read more…Would u prefer a RETURN TO TRANSMITTER FEATURE over the RETURN TO HOME feature?
Would you desire the ability to be able to move around and still have the abillity to have your drone return to your current location?
Would u like to have the abillity t
Read more…I am new to all this, and trying to figure out how to do rough calculations for drone configurations.
I'd like to be able to look at some motor spec sheets ... like this U15II monstor
http://store-en.tmotor.com/goods.php?id=731
and figure out with 4 mot
Read more…Hello drone experts!I'm building a x500 readytosky kit.Lots of small issues getting started but finally attached esc and motors to autopilot to do all in one calibration.The ESCs are cheap readytosky simonk 30A.Firstly I couldn't follow the throttle
Read more…