I have a APM 2.8 and am wanting to control a couple servos using telemetry connected to mission planner. is anyone aware of a way to do this? I will be using it for payload dropping and I don't want to use the camera shutter because Im using that for
Read more…Hi,
I'm hoping someone can help me - I can't for the life of me seem to get a reliable compass bearing from my setup. I've scoured the google-webs but just can't find anything that seems to fit.
In mission planner, I find that the bearing doesn't follo
Read more…Hi guys,
so in the title i mentioned the design im building is a semi vtol edf design from the concept art of the halo 5 wasp
so my plan since they dont make edf motors big enough or powerfull enough i will use multiple electric motors in a configuration to
Read more…Hello, I'm trying to do an autonomous flight indoors and I decided to program my APM 2.8 with a custom code using the AP library, when I test the sensor to measure Pitch Roll and Yaw, Pitch and Roll work fine, but Yaw starts to climb gradually to 180
Read more…Hi !
I'm setting my new FX61 with an APM2.6 on MP3.4
I have to trim one elevon in manual mode, so I try to change RC1_TRIM parameter but that does nothing !
Of course , if I trim the TX, the 2 elevons are affected...
After a long search, may be someone c
Hi friends:
Here is Pippa from EV-PEAK. Pippa is the sales of EV-PEAK. EV-PEAK is the manufacture of balance chargers for drones, RC cars, and FPVs.I am posting here for introducing balance chargers from EV-PEAK.If you interested in the chargers, you
Read more…Hello,
Is there any solution of getting GPS telemetry via audio channel trought FPV with Pixhawk Tracker ? ( http://ardupilot.org/antennatracker/index.html ). I want to have only FPV 5.8 Ghz antenne, so i can tracking and have FPV together. I saw the
I'm currently working on a S800 clone using a pixhawk flight controller. I could used some guidance on wiring things up.
I'm not quite sure where to get the wiring harnesses that will run from the pixhawk to the motor wiring pins on the center board.
Read more…An Antenna Tracker is a system that tracks the location of a vehicle and uses this information to aim a directional antenna.
The tracker described in this article uses the Mission Planner to determine the direction to aim the tracker using the positio
Hi Guys - my deepest apologies if this is both obvious and an old problem but its new to me and I need help.
I have been flying my Phantom 3 for a while but thought I would venture ito the DIY drone so...
I have assembled a flamewheel clone frame with
Read more…Hi,
I have a quad copter with tmotor air gear 350 combo pack esc and motors and with pixhawk 3.4.6 autopilot.
2 days ago my copter had a very strange behavior and as it was in auto mode for mapping at a turn it suddenly lost about 7-8 meters height and
Read more…This BBS was so attractive to me that I became one of them, and this was my first post, a little bit nervous, but it's ok.
According so much research, I've found out that GPS modules have so many factors that depend their performance on.
But I was init
Read more…Hello,I am new here and totally inexperienced. I have a need for a very small quad that can provide live video in a dark environment.Suggestions?Thanks
Read more…Dear Friends
I plan to buy a heavy lifting drone, by weight 50kg, 100kg and 200kg respectively, please recommand a proper suppler for me.
Regards
Steven
Read more…Hi there,
I have a quad co-axial multi-rotor drone and crashed during loitering mode. The drone was hovering about 10 m from the ground in loiter mode and then all of a sudden ALL motors stop spinning and finally crashed.
About this drone,
- MTOW = 25 k
Read more…WiFiBroadcast is an opensource digital FPV and telemetry system.
Main features:
- 1:1 map RTP to IEEE80211 packets for minimum latency (doesn't serialize to byte steam)
- Smart FEC support (immediately yeild packet to video decoder if FEC pipeline
I am planning to design an Arduino drone with a cloverleaf antenna. Already Googled cloverleaf leaf designs and tutorials separately. But didn't find the one with Arduino boards. Is it practically possible to lump Arduino with a cloverleaf antenna?
Read more…Hello guys, I am a mechanical engineering student, for my thesis, I am working on a Survey UAV. Now it is carrying a lot of electronics (about 170watt) so it gets quite toasty inside. I wanted to go with a water cooler on the cooling block of the ele
Read more…Hi there,
