I am using a Pixhawk2.1, RoboClaw motor controller and Mssion Planner to control a rover. I have most things working well except for one issue I cannot figure out. The PixHawk outputs to the RoboClaw on channels 1 and 3 using skid steering. Regardl
Read more…
Luckily to get three free Tattu R-line 4s 95c Lipo battery, and I then I test it for my Walkera F210. The Tattu R-Line 4s 1300mAh batteryperformed very well, punch-outs are even more impressive than with stock battery. I could say that also flight ti
Read more…Set up is getting limited flight times and I only just get in the air and start to set up my shots and it is coming down.
Please throw me a line for help to improve this situation.
T960mm, 1755" props, 4114 320KV Tarot motors, 2x6000MAh 6s 25C Tattu ba
Read more…Hello
I am a junior RC aficionado, have been going into drone´s world for last two years.
I have performed my own quadcopter with Pixhawk as flight controller. In maiden flight, when drone was armed and I tried to take it off, motors went crazy and dr
Read more…Hello,
I am building a light weight foldable quad (550 size) with some options : telemetry, MavLink_FrSkySPort, 3 axis gimbal for the lightweight Runcam Split; based on a 3DR Pixhawk Mini.
Thus I am wondering if it is possible to acces Serial2 port wit
Read more…Hi,
I purchased PIxhawk 2.1 and it came with its own Power Module (power brick). I assembled and configured a quadcopter. When I connected the battery that is fully charged everything works fine. However, if the battery is not fully charged (voltage s
Read more…Hi all,
I am hoping someone can help with a problem I am currently having. I will start by telling you what it is then I will give you some background information.
I am running APM 3.2.1. The flight performance is not what I am expecting so I had a l
Read more…Has anyone had any experience with integrating hobbyist ultrasonic (avoidance) sensors into the APM2.6/2.8 board?
These sensors are cheap and readily exsessable, seeing as the source code is open source these sensors could be relatively easily be add
Read more…Hello All,
I make the first drone and bought the motor B2212_920 and frame F450. I have my own motor controller and I can adjust the RPM. I will use 4S LiPo. Today, for the first time, I switched on the motors and dispersed up to 7,000 RPM with the pr
Hi friends,
Many discussions about this subject....
But no one about EXPO problem....
I fly with a joystick on USB port com in W7.
Every things is good but very much "agressive" control. I want to calibrate exponantiel. I know where is the control panel
Read more…Has anyone had any experience with integrating hobbyist ultrasonic (avoidance) sensors into the APM2.6/2.8 board?
These sensors are cheap and readily exsessable, seeing as the source code is open source these sensors could be relatively easily be add
Read more…I have a pixhawk px4 setup bundle with a Ublox M8N GPS/Compass. The compass works fine, the gps is blinking blue upon turning on the multirotor. And it flies fine without POS hold. However, with QGroundControl there is no Stats for the gps, no sateli
Read more…• #Massive quodcopter size!
• The best price in whole internet!
• The perfect #Drone to learn how to control #Quadcopter!
• Order here: https://TECHandPROMO.com
• Have questions? Contact our support team.
Hello Everyone,
I need advice for a project I want to do, and I will start by apologizing for terminology mistakes and grammar, I will eventually get better.
The project is a spherical drone, 45 cm in diameter, in which the propellers are enclosed insi
Read more…I have found a list of drone training courses around the world if anyone is interested c:
http://dronebusinessmarketer.com/drone-training/
I personally went with Total RPA as it was closest to me. I had a great and informative experience.
Where did eve
Read more…Hi everyone. Could anybody tell me how to make my walkera ilook camera connect to my monitor/receiver, as all I can get is a very grainy picture from very close up. The channels are supposed to correspond.
Thanks
Read more…I have a pixhawk px4 setup bundle with a Ublox M8N GPS/Compass. The compass works fine, the gps is blinking blue upon turning on the multirotor. And it flies fine without POS hold. However, with QGroundControl there is no Stats for the gps, no sateli
Read more…Hi friends,
Many discussions about this subject....
But no one about EXPO problem....
I fly with a joystick on USB port com in W7.
Every things is good but very much "agressive" control. I want to calibrate exponantiel. I know where is the control panel
Read more…hello everyone. im using mission planner to complete my degree.
my mission planner give this command when i want to download my log.
Getting list of log files...
Error:System.TimeoutException: Timeout on read - GetLogEntry
at MissionPlanner.MAVLinkInte
Hi friends,
Many discussions about this subject....
But no one about EXPO problem....
I fly with a joystick on USB port com in W7.
Every things is good but very much "agressive" control. I want to calibrate exponantiel. I know where is the control panel
Read more…