Road to Drone Autonomy Series is a 3-part series where we feature Drone Solution Providers (DSPs) from three different geographies from the European subcontinent to highlight the experiences and journey to adopting autonomous drone operations f
Read more…Hello everyone,
I've searched a lot about developing skills as a drone pilot. In my searches, Taking training to become a drone pilot from a particular academy is expensive.
Can you guys suggest to me, What are other ways to be skilled as a drone pil
Read more…Does anyone know the manufacturer of this drone?
I'd appreciate weblinks to the company.
Thanks for your help.
Hi,
I bought an IRIS+ in 2015 with a Tarus camera gimbal and flew it a few times-- including some auto Missions. Then I discovered 3DR had gone out of business and the copter has largely sat on the shelf for 7 years. I just bought 3 new batteries f
Read more…I'm looking for the cheapest possible 5 kg and 6 kg thrust brush and brushless motors to build throwaway dirt-cheap quad- and octocopter drones.
Read more…Please I need your help... I am in need of a company/ outlet to purchase... high volt . large capacity, Hi C rated Lithium battery packs. If you have any info please let me know. 96 volt... 24S around there ... but any info to get me started i
Read more…Howdy,
I'm looking for a design (parts list, assembly diagrams & instructions) for a dirt-cheap DIY quadcopter or octocopter cargo drone.
Because of the environmental conditions that it'll be facing, it's not expected to survive more than a few flight
I am looking for a reliable supplier of commercial grade Lithiul battery packs for an high lift UAV... 48 volt to 96 volt... any info would be very helpful Thank you
Read more…HI.
I am trying to find a supplier of good quality lithium battery packs. 48v to 96 volt... I am looking to work with them to produce several packs correct for my application,
Any info will be greatly appreciated.
Thank you...
Read more…I am in the SF Bay Area and need to get my multirotor up and flying for a research project. I am lookin for hands on help. The quad is built and ready to go with missiona planner but I am running into issues. I am looking for someone to go over thing
Read more…Ok so I know everyone recommends the radiomaster tx16s over the TX12 but it's $100 cheaper where I'm at.
My question is... Can the TX12 do pretty much the same things as the TX16s? I'm wanting to start a project building my own heavy lift drones and I
Read more…Hi guys,
We are currently making 4+1 quad plane using Pixhawk orange cube. In this recently we faced some issues while taking off the motor frame totally oscillating. We done manual and automatic Esc calibration and C.G position was proper. But stil
Read more…Hi everyone !
So I'm building my first drone and I'm kinda drown in all the technical specifities. I've found this build which seems easy enough :
Hi everybody,
I made a diy drone and specificatino is as below.
FCC : pixracer r15
ESC : Hobbywing Xrotor micro 60A 4in1
Motor : T-Motor 1300KV
When I tried to take off the drone, it can fly somehow.
But after flight Motor is too hot.
Is there any probl
Read more…Hi,
Guys, I need help completing my drone.
I have a naza, ran into problems with my taranis qx7 with and naza.
Will pay to setup.
Thx.
Read more…I'm looking to get back into ardupilot and I'm a little overwhelmed at the flight controller options. My last board was the original ArduPilot Mega from 10 years ago. I'm wondering if there is a reasonably priced, popular/standard flight controller o
Read more…F4 V3s Plus does not have IBUS port. Tried ti use, as advised a free UART. Inmy case RX 6 and set:
serialrx_halfduplex=OFF
serialrx_inverted =OFF
I did set the receiver to IBUS as well as on my FS-i6 RC.
That did not solve the problem.
I tried another app
Read more…I am looking for vision-based navigation systems. Imagine an environment where no GPS or RF connection to the drone is available. Can a drone navigate by (for example) looking straight down and following a road network?
This project is crucial, and
Hello, I have a project which requires a gas tank sensor to talk to the APM 2.8 The gas tank sensor is the typical 0-190Ω variety like this:
Read more…