Dear Experts,
Someone had experience with this video grabber and Ordroid XU-4 board ?!
http://febon.blogspot.com/2014/08/febon198-usb30-uvc-hdmi-grabber-card.html
my goal is to acquire a 1080p@30fps stream (H.264 or RAW) from GoPro 4 Black through HDMI
Read more…Hello to everybody,
One of the most challenging things for drones constructors to overcome is to prove the reliability of the autopilot system used.
I was wondering If any quantitative reliability assessment at least for Hardware components has been do
Read more…Hello to everybody,
Is it possible with mission planner to pause a mission at run time?!
I have a hexacopter with APM 2.5 (AC ver 3.0.1) programmed to fly over a testing area with Mission Planner (ver 1.3.7). The idea is plan an auto mode mission with
Read more…Hi guys,
I had a strange crash with my foam quad in auto mode. The quad frame is the following:
It's a pretty big frame and ver
Read more…I was wondering if this Futaba compliant FrSky Receiver TFR4 SB supports also PPM Out as the well known FrSky TFR4. I'm afraid it does not...Anybody had any experience with it ?
Thank you.
Alberto
Read more…Hi,
I had a very strange crash with my quad. I made dozens of successful missions with APM 2.0 - 2.9.1b Arducopter firmware. I felt this platform was very stable and did not upgrade to 3.0.1 on this frame.
Well I had a crash few seconds after taking of
Read more…Hi everybody,
I'm running arducopter 3.0.1 (hexa X configuration) on Mission Planner 1.2.69 with internal magnetometer. For some reasons the copter did not arm last time and I realized that on CLI mode under test->compass the magnetometer did not res
Read more…Hello to everybody,
I've got a problem with my APM 2.5 with both internal and external compass. I'm running arducopter 3.0.1.
When I go on CLI in test section, all the tests on the other sensors like GPS and baro works great, but if i go on test->compa
Read more…Hello to everybody,
I have an Hexacopter running Arducopter 3.0.1 with Mission Planner 1.2.62. I could not find on the copter parameters the possibility to setup and enable the gimbal pan and tilt parmaters as it was for 2.9.1b and older version of Mi
Read more…ciao Tutti,
Sto provando a capire il comportamento del mio nuovo Hexacopter in modalità Loiter e Alt hold.
Il comportamento della piattaforma in modalità stabilize sembra buona; è stabile e molto docile, sebbene abbia una leggerissima tendenza ad imbar
Read more…Hi,
I have a medium size FY680 Tarot Iron Man Hexa Frame of about 3 Kg at full load with 8000 mAH 4S battery pack. The platform is very stable and smooth in stabilize mode, but it overshoots when I switch to Lotier and alt hold; When I switch in those
Read more…Hello to everybody,
I've got a problem on the compass on my APM 2.0: On CLI it results always as "not Healty", with always the same initialization message "Compass init error". I tried to download the firmware of ArduCopter from 2.9.1b to 2.9.1 and 2.
Read more…I was trying a very first basic configuration with APM 2.0 for altitude hold and loiter for my FY450 quad and I noticed that in LOITER mode with low wind, quad started little by little to lose its initial position making bigger and bigger circles aro
Read more…Hi,
I was trying to use the Channel Output 6 of UDB - RED Board - to control a Camera. My purpose is to keep the camera fixed at the launcing point during all the UAV mission. I was trying my first tests with the Yaw axis. I understand the camera yaw
Read more…Hi,
I used the UDB HILPlugin for Xplane on both Windows and Mac using the compiled binary for both operating systems. On windows everything works fine; using the same configuration of the setupHILPlugin file on Mac I can control the airplane but both
Read more…Hi,
I successufully configured the UDB Red Board with MatrixPilot software (2_5_1 version) and managed to perform the first tests on Xplane with HILPlugin, but there's still something I did not get yet:
