About

Gender

Male


Please tell us a bit about your UAV interest

Preparation for First Person Flying


Hometown:

Marburg


Activity Feed

Andi replied to Andi's discussion No Power on Telemetry port
"i will check the cable later, but i thought i tested it already, was ok. However, if it is not the cable what could it be? Power module? Has it seperate circuits for the APM itself and the peripherals?"
Jul 22, 2015
Andi replied to Andi's discussion No Power on Telemetry port
"unfortunatly it's not that easy, all pins are ok...."
Jul 22, 2015
Andi posted a discussion
Hey guys,i'm currently facing a problem i don't really understand. The Telemetry module connected to APM don't get power. The module itself is ok, tested on PC:The APM 2.5 is powered via the 3dr Power module and everything is working fine, besides…
Jul 21, 2015
Andi replied to Andi's discussion 3dr links only works with usb
"thanks for the suggestion but i do not connect the apm via BEC:

however to disconnect the radio i have to disassemble the whole copter, this is a lot more complicated than it should be. well will do it in the next few days. I hoped their might be…"
May 25, 2014
Andi replied to Andi's discussion 3dr links only works with usb
"Well it's simple. if the copter is powered with lipo my ground radio is not going to connect, it keeps green blinking.

But if i disconnect the lipo from the apm and connect the APM via USB to the PC too, both connect immediatly and stop blinking."
May 25, 2014
Andi replied to Andi's discussion 3dr links only works with usb
"this is mainly the config of both. As i said, if connected via usb they both find each other, so i'm pretty sure it's not a settings issue, maybe you can tell me what you are looking for."
May 25, 2014
Andi replied to Andi's discussion 3dr links only works with usb
"sure...

S0: FORMAT=25S1: SERIAL_SPEED=57S2: AIR_SPEED=32S3: NETID=25S4: TXPOWER=8S5: ECC=1S6: MAVLINK=1S7: OPPRESEND=1S8: MIN_FREQ=433050S9: MAX_FREQ=434700S10: NUM_CHANNELS=10S11: DUTY_CYCLE=20S12: LBT_RSSI=0S13: MANCHESTER=0S14: RTSCTS=0"
May 24, 2014
Andi posted a discussion
Hi Folks,after i dig out my copter for about one year of absence the first i did was updating it to the new arducopter firmware. However, everthing works fine while connected via usb.then i unplugged usb, put my 3dr radio into the pc and powered the…
May 23, 2014
Andi replied to helmut pechmann's discussion apm2.5 motoren ausschalten durch einen schalter an der fernsteuerung. in German Ardu-Group
"Ja ich versteh dein Problem, aber ich versteh nicht warum man das möchte das die Motoren sich weterdrehen. Selbst wenn man ausversehen den gashebel ganz runterknallt und wieder hoch drehen sie sich schnell genug wieder an. Ist mir persönlich aber…"
Sep 14, 2013
Andi replied to helmut pechmann's discussion apm2.5 motoren ausschalten durch einen schalter an der fernsteuerung. in German Ardu-Group
"Verstehe das Problem nicht so ganz, wenn du den Gasknüppel ganz nach unten ziehst drehen sich doch die Motoren nicht? Da hast du doch alle Zeit zu disarmen? Quasi wie bei einem normalen Flugzeug."
Sep 14, 2013
Andi replied to Andi's discussion jdrones ioboard CTS / GND connected in ArduCopter User Group
"strange, it must have been something with the nature of my question that nobody is able to answer it.... sigh."
Sep 10, 2013
Andi posted a discussion in ArduCopter User Group
Hi guys,maybe one of you can help me get the IOBoard running before i try and fry.Because the support of jdrones seems to be ignoring my ticket weeks ago, and also my other ticket with a reminder (well for me a reason not to buy there again)after…
Sep 9, 2013
Andi posted a discussion
Hi there,i need a voltage of 5v for my video TX. The Boscam 5813 needs a current of 180 regarding the specs.The A0 - A9 headers plus and minus should be sourced by the 3dr powermodule, right?I'm using the 3dr 60A power module which should support up…
Sep 7, 2013
Andi replied to Randy's discussion ArduCopter-3.0.1 released!
"Short story... when the 3.0.1 was released i immediatly installed it with the result the copter was unflyable.
I did a erase of the EPROM rolled back to 2.9.1b and had one of the most successful flight ever. Loiter was holding the position approx at…"
Jul 18, 2013
Andi replied to Randy's discussion ArduCopter-3.0.1 released!
"unfortunatly it seems you removed the 3.0.1 from the MP?

it now shows again 2.91b"
Jul 15, 2013
Andi replied to Thorsten Hinz's discussion Problem in der Luft in German Ardu-Group
Feb 20, 2013
More…