Gender
Male
About
Location
Gaithersburg, MD
Please tell us a bit about your UAV interest
Noob Looking to have fun and maybe try FPV
Hometown:
Gaithersburg MD
Activity Feed
"Wow Thanks Jim
I changed the suspicious motor and all is well now. The information you gave was very helpful."
I changed the suspicious motor and all is well now. The information you gave was very helpful."
"Thanks Jim,
These are good ideas. I thought one of the motors seemed weird, thus the yaw on take off. I will check the things you mentioned. And yes I am in Stabilize I do not have enough time to switch modes, it cuts the power that fast even with…"
These are good ideas. I thought one of the motors seemed weird, thus the yaw on take off. I will check the things you mentioned. And yes I am in Stabilize I do not have enough time to switch modes, it cuts the power that fast even with…"
I take off ok, it is a little rough wants to yaw but it gets up in the air and seems to be ok. Then it starts to come down so I give it throttle. It seems like it has less and less power and finally just lands. This takes about 15 seconds. I can…
"Can anyone give me any ideas on where to look to see where these spikes in the accelerometer data are coming from. It seems that when they occur I get a 3 to 6 meter drop in altitude. I have only seen this in ALTHOLD but that maybe coincidental.…"
When I go into logs and type > enable raw It should come back and show me that raw is enabled, right?When I type enable RAW it just comes back with the logs that are already enabled with no RAW. What I am doing wrong?Thanks
"If you order new motors do they come with the new prop adapters.
"
"
"Ramon,
I have over $200 in my cart I am waiting to purchase. I would like to apply my credits to this order. Please let me know when the credits are in the account so I can complete this transaction.
Thanks
Chuck
"
I have over $200 in my cart I am waiting to purchase. I would like to apply my credits to this order. Please let me know when the credits are in the account so I can complete this transaction.
Thanks
Chuck
"
"Ramon,
I did not get that email Make sure it went to outman@his.com
Thanks
"
I did not get that email Make sure it went to outman@his.com
Thanks
"
"When are you available. I still cnnot get into the website. I just tried chrome... no difference
"
"
"Not sure this is you issue but If you were connected when you tried to load the firmware it will give you that error. Try disconnecting then load the firmware."
"I have tried the latest and I also had a problem moving the Quad in Loiter. I was a lttle scared the first time it happened there was very little response to pitch or roll. Full left on the stick the quad would barely move."
"Mine is I am mixed with channel 6
Gear 0: Flap 0 -> CH5 1610/ CH6 1912 Flap 1 -> CH5 1702 / CH6 1516 Flap 2 -> CH5 1793 / CH6 1120lGear 1: Flap 0 -> CH5 1199 / CH6 1912 Flap 1 -> CH5 1358 / CH6 1516 …"
Gear 0: Flap 0 -> CH5 1610/ CH6 1912 Flap 1 -> CH5 1702 / CH6 1516 Flap 2 -> CH5 1793 / CH6 1120lGear 1: Flap 0 -> CH5 1199 / CH6 1912 Flap 1 -> CH5 1358 / CH6 1516 …"
"The movement of AX1 is not nearly enough. I might suggest that you go back to the settings outlined from Bruce and go to the flight planner radio calibration and see what the pwm values are when changing the Gear 2 position switch and the flaps 3…"
"What are you seeing? On the radio, if it is set right and you go to "Servo Setup" and move the Flap toggle and the gear toggle you should the GER and AX1 bars move on the Servo screen. If you do not see them move your radio is not set up correctly.…"
"Tanks to the OP for this. I got it to work for all 6 modes. The only thing I changed was instead of -85% in MIX 2 I dropped it to -50% and I get all 6 flight modes on channel 5
This is for a DX7S and an AR8000"
This is for a DX7S and an AR8000"
